A W8x15, A36 steel is used as a simply supported beam uniformly loaded over a span of 5.9 m. If the top flange is continuously braced against lateral displacement by the floor, calculate the allowable uniform load the beam can sustain against bending about the major axis by ASD. Write your answer in kN-m with 2 decimal places only. Use Zz - 223 x 103 mm3

A W8x15, A36 steel is used as a simply supported beam uniformly loaded over a span of 5.9 m. If the top flange is continuously braced against lateral displacement by the floor, calculate the allowable uniform load the beam can sustain against bending about the major axis by ASD. Write your answer in kN-m with 2 decimal places only. Use Zz - 223 x 103 mm3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Steel structure
Please show all work provided for the following problem so I can understand. Please show step by step solutions with neat hand writing.
The below figure represents a section of a pre- stressed beam. For a no-tension design where a is the permissible stress in concrete, the total moment carrying capacity is (a) (c) d/2 bd² 6 d/2 bd²oc 3 -b- (b) (d) bd² oc 4 bd²a 12
Question 2: An unsymmetrical flexural member consists of a 3 × 22 top flange, a 3 × 16 bottom flange, and a ½ × 66 web. a. Determine the distance ỹ from the top of the shape to the horizontal plastic neu- tral axis. b. If A572 Grade 50 steel is used, what is the plastic moment M, for the horizontal plastic neutral axis? c. Compute the plastic section modulus Z with respect to the minor principal axis.
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows: Ag = 14,500 sq.mm, Ix= 258.6 x10^6 mm ^4 Iy=84.375 x 10^6 mm^4. 57. Calculate the flexural buckling stress Fcr in MPa
A WT205 × 30 structural steel section (see Appendix B for cross-sectional properties) is used for a 6.4 m column. Assume pinned connections at each end of the column. Determine:(a) the slenderness ratio.(b) the Euler buckling load. Use E = 200 GPa for the steel.(c) the axial stress in the column when the Euler load is applied. Use Appendix B to look up the cross-sectional area, the area moment of inertia, and the radius of gyration for a WT205 x 30 structural steel section.Answer:A = mm2Ix = x 106 mm4rx = mmIy = x 106 mm4ry = mm
Compute the design shear strength of an M10 x 9 of A242 steel. Fy = 50 ksi. Blank 1 d = 10 in tw = 0.157 in h/tw = 58.4 Blank 1 Add your answer
1. An unsymmetrical flexural member consists of a 70 × 600 top flange, a 70 x 400 bottom flange, and a 12 × 180 web. a, Determine the Section Modulus. b. Determine the distance from the bottom of the shape to the horizontal plastic neutral axis. c. If A572 Grade 50 steel is used, what is the plastic moment MPy for the horizontal plastic neutral axis?
PROBLEM 4: The beam shown the figure below is a W16x31 of A992 steel and has continuous lat- eral support. The two concentrated loads are service live loads. Neglect the weight of the beam and determine whether the beam is adequate. a. Use LRFD. b. Use ASD. 60k 60k W16 x 31 asap +4
Design the most economical member for truss member L1 of the truss shown below. It is to consist of a W flange with a three lines of 16mm bolts in each flange element. Using A36 steel with an Fy = 250 MPa and Fu = 400 MPa 3.6000 Pu-100 KN 3.6000 Section Name W12x14 W12x65 w12x17 Pu= 100 KN Area (mm²) 2680 12300 2720 3.6000 Pu-100 KN d (mm) 302 307 305 3.6000 tf (mm) 5.72 Pu= 100 KN 15.4 12.4 -3.6000- bf (mm) 101 305 205 Pu-100 KN 3.6000 3.6000
AW18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P= 20 kips, w = 5.8 kips/ft, LAB = 4.0 ft, LBc = 4.0 ft, and LcD = 13.0 ft. Determine the magnitude of the maximum bending stress in the beam. A В C D LAB LBC LCD Answer: Omax i ksi
HOMEWORK-1 3m IF For the truss shown in the figure; Design members 1-2 and 2-3 assuming that out of plane deflections are restrained and Ner>>10, i.e. global buckling is not the critical failure mode and therefore linear static analysis is sufficient. P.S. Use square rectangular hollow sections in Grade 355 steel. You will have to find the related section tables from the internet. Do not forget to refer to the related EN1993-1-1 tables and equations. Later, you will design the connections (the weld lengths, etc.) and the supports for this problem.