Situation 1: A W8x31 simply supported beam carries auniformly distributed load. The properties of the sectionrelevant to the problem are as follow: Use A50 steel and Cb- 1.14d=203 mmbf = 203 mmtf-11.0 mmtw = 7.24 mmkdes - 21.1 mmry = 51.3 mmIx = 45.8 x 10^6 mm^4ly- 15.4 x 10^6 mm^4Sx-451 x 10^3 mm^3Zx = 498 x 10^3 mm^3J-223 x 10^3 mm^3Cw-142 x 10^9 mm^61. Which of the following nearly gives the maximum safeuniform load (Wu) that the beam could carry if the spanof the beam is 5m? Neglect weight of the beam.46 KN/m41 KN/m51 KN/m33 KN/m

Answered: Image /qna-images/answer/37ffd860-f332-4c4b-8065-468b2c8d6e04.jpg

Situation 1: A W8x31 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb -1.14 d = 203 mm bf - 203 mm tf-11.0 mm tw = 7.24 mm kdes - 21.1 mm ry = 51.3 mm lx = 45.8 x 10^6 mm^4 ly - 15.4 x 10^6 mm^4 Sx-451 x 10^3 mm^3 Zx = 498 x 10^3 mm^3 J-223 x 10^3 mm^3 Cw-142 x 10^9 mm^6 1. Which of the following nearly gives the maximum safe uniform load (Wu) that the beam could carry if the span of the beam is 5m? Neglect weight of the beam. 46 KN/m 41 KN/m 51 KN/m 33 KN/m

Situation 1: A W8x31 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb -1.14 d = 203 mm bf - 203 mm tf-11.0 mm tw = 7.24 mm kdes - 21.1 mm ry = 51.3 mm lx = 45.8 x 10^6 mm^4 ly - 15.4 x 10^6 mm^4 Sx-451 x 10^3 mm^3 Zx = 498 x 10^3 mm^3 J-223 x 10^3 mm^3 Cw-142 x 10^9 mm^6 1. Which of the following nearly gives the maximum safe uniform load (Wu) that the beam could carry if the span of the beam is 5m? Neglect weight of the beam. 46 KN/m 41 KN/m 51 KN/m 33 KN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

solve the given and show your complete solution.
please help my homework.thank you very much. my questions subject is fundamentals of steel design
A W6 x 15 structural steel column is 24 ft tall and is fixed at its base and top. It is braced (horizontally) at the midspan. These braces are pin-connected to the column's web. Determine the load that the column can support so that it does not buckle nor the material exceeds the yield stress. Use the undermentioned data: Q2 E = 29 (10)³ ksi Oy = 60 ksi %3D Ik = 29.1 in ly = 9.32 in (This question has no diagram)
A W16X31 A992 steel is used as a beam. The beam has a continuous lateral support. The uniformly distributed load shown in the figure is a service load that consists of 50% dead load (included the beam weight) and 50% live load. Using LRFD, determine the following? Note: A992 STEEL Fy = 50 ksi Ag = 9.13 in^2 Zx = 54.0 in^3 What is the Ultimate (Governing Load Combo) Maximum Positive and Negative Moment (at midspan) in kips-ft
The beam has a cross section shown in the figure. fc’ = 26 MPa, fy = 390MPa, determine the following:a. The minimum steel area permitted by the NSCP Specs.b. The flexural design strength Mu if it is reinforced with minimum steelarea.c. The maximum area of flexural steel that can be used in reinforced thesection.
Topic: Introduction to Steel Design Problem: For the section shown: a. Determine the moment of inertia with respect to the x-axis b. Determine the moment of inertia with respect to the y-axis
Does the column shown in the figure have enough availablestrength to support the given service loads?a. Use LRFD.b. Use ASD.
A simply supported wood beam having a span length L = 12 ft is subjected to unsymmetrical point loads, as shown in the figure. Select a suitable size for the beam from the table in Appendix G. The allowable bending stress is 1800 psi and the wood weighs 35 lb/ft3.
Truss by Method of Joints Determine the force of the truss shown in Fig.
1. Determine the x and y coordinate of the shaded area shown in the figure below. 10 80 10 All units are in cm 10 40 PSD323- Principles of Steel Design 2. For the shaded area in the Figure shown, determine the following: a. The area of the shaded portion in square millimeters b. The x-coordinate of the centroid of the area in mm c. The moment of inertia of the composite area with respect to the x-axis in mm^4 45 mm mm 3. For the shaded area shown in the figure below, determine the following: a. The area of the shaded area in square millimeters b. the x coordinate of the centroid in millimeters c. the y- coordinate of the centroid in millimeters. 400 e 200 200 400 All units in mm PSD323- Principles of Steel Design
In situations 2 Solve 6-7-8-9-10 ok Handwriting Solutions ok thanks ?
Topic: Stresses in Beams Instructions: Find the value of: y = C = A' = y' = I =