A W360X101 is used as a 7.3 m - long column with pinned end supports. The column is laterally supported (braced) in the weak direction at the one- third points of the total column length. Use ASD and Fy= 345 MPa. If the column will carry a service axial dead load of 891 kN, calculate the service axial live load (kN) it can carry.

A W360X101 is used as a 7.3 m - long column with pinned end supports. The column is laterally supported (braced) in the weak direction at the one- third points of the total column length. Use ASD and Fy= 345 MPa. If the column will carry a service axial dead load of 891 kN, calculate the service axial live load (kN) it can carry.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Similar questions

Asap
A W36x210 can be used for Transfer Girder ‘A’ as shown in the elevation next page.Assume the LRFD loads on the ‘Transfer Girder’ are as follows:Pu= 200 kips from the column above. Assume also that the loads from self-weight of thewu = 2.0 kip/ft (girder self weight and beams framing into this transfer girder are equivalentto a uniformly distributed load). These loads are shown in the last figure.a) Check whether the W36x210 ‘Transfer Girder’ is adequate for bending and shear.Assume the unbraced length Lb =20 ft.b) Suppose that service loads, w and P, are both 50% dead load and 50% live load. Does theW36x210 satisfy a service live load deflection limit of L/480?
A W530x92 supports a uniformly distributed load of 12 kN/m (including the weight of the beam) and equal concentrated load P at quarter points (L/4, L/2, and 3L/4). The compression flange is laterally supported at quarter points and at the ends. The beam is 12m simply supported. Using A36 steel, the beam has the following properties: d = 533 mm %3D bf = 209 mm %3D tf = 15.6 mm tw 10.2 mm %3D k = 32 mm ry = 44.9 mm %3D Sx = 2070 x 10^3 mm^3 Zx = 2360 x 10^3 mm^3 Es = 200,000 MPa %3D \x 3 552 х 10^6 MРа Find the maximum allowable load P so that it will not exceed its maximum allowable moment capacity. Use conservative assumption for Cb. Consider all the necessary failure that could happen.
A W530x92 supports a uniformly distributed load of 12 kN/m (including the weight of the beam) and equal concentrated load P at quarter points (L/4, L/2, and 3L/4). The compression flange is laterally supported at quarter points and at the ends. The beam is 12m simply supported. Using A36 steel, the beam has the following properties: d = 533 mm bf = 209 mm tf = 15.6 mm tw = 10.2 mm k = 32 mm ry = 44.9 mm Sx = 2070 x 10^3 mm^3 Zx = 2360 x 10^3 mm^3 Es = 200,000 MPa Ix = 552 x 10^6 MPa Find the maximum allowable load P so that it will not exceed its maximum allowable moment capacity. Use conservative assumption for Cb.
A built-up section consisting of W 350 x 90 which 15 mm plates welded to form a box section as shown in figure. The section is used as a column 12 m meters long carring a deadload of 2000 kN. The column is braced at both ends, and braced at mid height about the weak axis (Y-axis). Use Pu = PD + PLL for allowable axial load and Pu = 1.2 PD+ 1.6 Pu for service axial load. Fy =250 Mpa. Properties ; bf = 200 mm Ix = 324 x 106 mmª tf = 22.5 mm ly = 57.34 x 106 mm4 d = 400 mm tw = 15.2 mm 200 mm 400 mm ++ I5 mm 15 mm W 350 x 90 a) Determine the axial live load of the column using the ASD 2015 NSCP. b) Determine the safe service live load of the column using the LRFD 2015 NSCP.
A W24x250 is used as a beam to support a one-way concrete slab floor system. The floor is to carry a totalload of Y kPa (30% DL, 70%LL, self-weight is included in DL). The beam is simply supported over a span ofW/2 m. Assume the beam is laterally supported over its length. Use Fy = 248 MPa. Allowable deflectionfrom service loads is L/360. Use ASD. a.What is the center-to-center spacing of the beams (m) based on shear capacity? b.What is the center-to-center spacing of the beams (m) based on flexural capacity?C.What is the center-to-center spacing of the beams (m) based on allowable deflection? Reference datas: W= 25 mm , 25 MPaW/2 = 12.5 mW/4 =6.25mX=475 KNY= 155 KN, 155 KPa, 175 mmZ=60×+Z=535mm
A W360X110 is used as a 7.3 m - long column with pinned end supports. The column is laterally supported (braced) in the weak direction at the one-third points of the total column length. Use LRFD and Fy = 345 MPa. If the column will carry a service axial dead load of 918 kN, calculate the service axial live load (kN) it can carry.
A W14 x 74 compression member carries a service loads of DL= 2,500 KN and LL= 300 KN. The column is fixed at the top end and pinned at the bottom. The length is 6 m. If A992 steel (Ex= 350 MPa and F₁- 450 MPa) is used, check the adequacy of the column. Check also the column stability. Use ASD.
The I-beam section shown below is simply supported over a span of 6 m, what is the service uniform live load it can carry if the total dead load including beam weight is 12 kN/m? Use d = 700mm, f = 21 MPa and fy = 420 MPa. 100 3-025 -300- 100 540 120 760
A W14 x 90 of A992 steel (Fy= 350 MPa and Fu= 450 MPa) is used as a 4.25 m (14 ft) long beam-column with Kx= 0.9 and Ky= 1.0. The member is braced against sidesway, the ends are restrained, and there are transverse loads between the ends. The member is subjected to the following service loads and moments: an axial compressive load of 1520 KN and a bending moment of 335 KN.m about the strong axis. The composition of each is 35% dead load and 65% live load. Use Cb= 1.6 and consider moment amplification. Use LRFD
1. Design the most economical A36 steel base bf plate to resist a dead lgad = 1,400 kN and a live load = 1,700 kN. The column is supported by a m 700 mm x 700 mm concrete pedestal with fc' = 27 MPa. The column section used is W14x500. d. 0.95d N A W16x100 is used as a column to carry an axial load of 1,200 kN. Design a base plate to support the column such that m & n_are approximately the same. The base plate is to rest fully on a concrete pedestal with fc' = 21 MPa. Use A50 steel base plate. 2. m •0.80bf n RING
Q-An RC square column of size 600 mm is constructed to carry an unfactored load of 3000 kN. The ends of the column are restrained from displacement but free to rotate and is casted with M-25 concrete. The area of Fe-415 steel required to carry the given load considering that the column is short and loaded with minimum eccentricity is