A compression member is 8 m long and is pinned at the top and fixed at the bottom and is braced at midspan about its weak axis (axis with lower value of moment of inertia). The propertiesof the column section are as follows:AreaMoment of Inertia, IxMoment of Inertia, lyWhich of the following most nearly gives the maximum length of the column so that the proportional limit of 320 MPa will not be exceeded?Select the correct response:10.79 m16.62 m3.78 m8,129 mm²178.3 x 106 mm418.8 x 106 mm47.55 m

Answered: Image /qna-images/answer/c5e5f1f2-9837-48a6-85f7-0ea1df892f9f.jpg

A compression member is 8 m long and is pinned at the top and fixed at the bottom and is braced at midspan about its weak axis (axis with lo of the column section are as follows: Area Moment of Inertia, Ix Moment of Inertia, ly 8,129 mm² 178.3 x 106 mm4 18.8 x 105 mm4 Which of the following most nearly gives the maximum length of the column so that the proportional limit of 320 MPa will not be exceeded? Select the correct response:

A compression member is 8 m long and is pinned at the top and fixed at the bottom and is braced at midspan about its weak axis (axis with lo of the column section are as follows: Area Moment of Inertia, Ix Moment of Inertia, ly 8,129 mm² 178.3 x 106 mm4 18.8 x 105 mm4 Which of the following most nearly gives the maximum length of the column so that the proportional limit of 320 MPa will not be exceeded? Select the correct response:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

With fbd diagrams please
Solve with FBD thank you
Determine the ultimate moment capacity of the beam shown using this data: bi = 900 mm t = 100 mm d = 450 mm As = 9852 mm² bw = 300 mm fy =276 MPa f'c = 28 MPa br As bw
1. The I-section shown below Is to be used as part of a roof truss. Compute for the centroid and the moment of Inertia 20 mm 140 mm 100 mm 20 mm 100 mm 20 mm
A uniform concrete slab is to be attached to two rods whose lowers ends are initially at the same level. What is the required area, in mm², of aluminum rod so that slab will remain level after it is attached to the rods? 4 m Aluminum E = 72 GPa Steel A= 96 mm < E = 200 GPa 4 m 3 m- 0.50 m
Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional Area Modulus of Elasticity AB 1,400 mm2 200 GPa BC 1,800 mm2 200 GPa DB 1,400 mm? 200 GPa C BY 18KN 400mm 400mm 400mm 55.00° 55.00°
Compute the moment of inertia: lown axis (in.4) Ay (in.4) Area y Part (in.2) (in.) Compression zone 12 x 6.51 78.12 6.51/2 276 828 Top steel 8.40 (6.51 – 2.5) 135 Bottom steel 19.2 (6.51 – 21.5) 4314 - I = 5550 in.*
You can assume all angles are either or . If the maximum compression or tensile force each beam can withstand is 4 N, what is the maximum mass that can “drive” across the truss (i.e., be applied at A, B, and C, sequentially)?
E=60 KN A=40 KN
QUESTION: Can you please explain where did the "10" from 8/10 and 6/10 came from?
333
An A36 Channel compression member of 2.88m length is laterally supported at mid-length on its major axis and at third points on its minor axis. The member has fixed supports at both ends. The properties of the channel section: A=1135mm2 , Ix=0.86x106 mm4 , Iy=0.13x106 mm4 . Calculate the maximum Slenderness Ratio of the member. Express your answer in 2 decimal places.