A W10x30, 2.8 m long, A36 steel is used as a column with pinned ends to support an ultimate dead load of 110 kN and live load of 289 kN. Calculate the maximum service wind load the column can sustain using LRFD. Use theoretical value of k. Write your answer rounded to the nearest whole number in kN . Use 1.2D + 1.0L + 1.0W load combination.

Q: W= 20000 N 2. There is a gap between the aluminum bar and the rigid slab that is supported by two…

A:

Q: 1. Determine the nominal axial compressive strength for the following cases: a. L= 15 ft b. L= 20 ft…

A: For L = 15 ft Use AISC equation ; Type of connection = Both ends are hinged So, Axial compressive…

Q: Q2: Design a round spiral column to support an axial dead load Po of 240 k and an axial live load P,…

A:

Q: Given: T Beam A shown below spans 32 ft (simple span) and supports the floor system shown. Typical…

A:

Q: 32 The simple beam is loaded with service loads in adition to its selfweight. Check if the…

A:

Q: . A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel bars having fy…

A:

Q: Problem A spiral column 600 mm in diameter has an unsupported height of 2.4 m. The column is bent in…

A:

Q: A simply-supported T-beam is subjected to two pairs of distributed loads: pair 1 (??1, ??1) and pair…

A: Answer  (1) Calculation of height of compression stress block  Let us calculate ultimate moment on…

Q: l: A short column is designed to carry a factored load (P) = 2140 kN and factored moment (M₂) = 690…

A: gcnbvnbvkjmbvkjhv

Q: 11. A W14x132 A992 column has an effective length of 36 ft about both axes. Determine the available…

A: Given  Column W14× 132  Effective length of column in both axes= 36 ft

Q: A W 530 x 101 supports the load shown in Figure below. Determine the maximum allowable distributed…

A:

Q: Select an economical rectangular beam sizes and select bars using A strength method. The beam is a…

A: Given:- wD=25kN/m wL=20kN/m f'c=28MPa fy=400MPa span=12m To find:- rectangular beam size

Q: A column in a building is subjected to the following service load effects: Dead Load = 40 KN Wind…

A:

Q: The following loads were computed for designing a column in a  frame: • Dead Load = 200 K • Roof…

A: Given values,Dead load, D = 200 kLive load from floors, L = 250 kLoad from roof, Lr=50 kCompression…

Q: e loads and dead loads act in a

A: To find: We have to find whether the given statement is true or false.  Given: Live loads and dead…

Q: Design a square tied column to support an axial dead load D of 130 k and an axial live load L of 180…

A:

Q: The floor of one-story office building in the figure is made of 4-in.-thick normal weight concrete.…

A:

Q: A built up steel column has section shown in figure which is used to support a square (16 ft)…

A: Slab 16ft X 16 ft X 8 inLive Load, WL = 100 psfDead Load, WD = 40 psfEffective length, KL = 6…

Q: A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if…

A: Maximum Bending stress calculation of Beam

Q: Homework - Bending Stress A 16-foot-long (4.88m) single overhang beam is loaded as shown. Assuming a…

A: L = 16 ft W8 x 35

Q: A cantilever beam has a length of 3 m and 400 mm depth. Is the beam depth permissible by the code?…

A: Given , length of beam =3m=3000mm Depth=400mm Ratio of length to depth =3000/400 =7.5:1 But code…

Q: A steel column has the following properties: E= 200 GPa, Fy = 200 MPa, L = 6 m, A = 8000 mm², ly =…

A: Answer  We are given E = 200 GPa = 200000 Mpa Fy = 200 Mpa L = 6 m = 6000 mm A = 8000 mm2  Iy =…

Q: Example_2: A cantilever beam as shown below has a rectangular cross section of b=200mm, d=390mm,…

A:

Q: A single dueling house has interior columns that are spaced 4.2 m apart in two perpendicular…

A: S = 4.2 mLL = 1.2 kN/m2

Q: Note: please use set B data 2° 3 MB A C 4m 2 m The cantilever beam above is made up of concrete with…

A: Given  A fixed beam  Required  Moment reaction at Support A

Q: A 5-m long, simply supported beam is loaded as shown. Determine the lightest W-shape beam that can…

A:

Q: 23. Live loads and dead loads act in a horizontal direction. a) False b) True

A: Statement: Live loads and dead loads act in a horizontal direction. To calculate: above statement is…

Q: Analysis of T beam with compression steel. Calculate the ultimate moment of resistance of a T beam…

A:

Q: Determine the governing (LRFD) axial load (kN) for a column in a multistory office building using…

A: Solution -The given values are as follows,The Live load= 149kNThe live load on floor=5.0KPaThe total…

Q: Note: please use set B data W 2° Me A B C * 4 m 2 m The cantilever beam above is made up of concrete…

A: Concept:- Here concept of area moment is state by two theorem  Theorem 1:-- area between M/EI…

Q: A 410-mm-diameter, non-slender, spiral column is symmetrically reinforced with 8-20 mm vertical…

A: Calculate design strength of column

Q: snip

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Example 5.2 A column section I.S.H.B.350 @ 661.2 N/m carries an axial load of 1100 kN. Design a…

A:

Q: Does the column shown below have enough available strength to support the given working loads?Use…

A: Property of column section: Length= 20 ftE = 20232 ksi , ry = 2.3 inch, K= 1.0 , Fy = 59.0 ksi, Ag =…

Q: A W21×101 is used as a compression member with one end fixed and the other end free. The length is…

A: Section-W21×101L=12 ftFy=50 ksi To find- Nominal compressive strength

Q: An ASTM A36 (Fy=36ksi) wide flange column has a length of 16.5feet and fixed ends. If rx=4.59in,…

A: The given data is shown below: Fy=36 ksiLength=16.5ftrx=4.59 in.ry=1.55 in.A=6.59 in.2E=29000 ksi

Q: A unreinforced concrete beam is 6in wide and 12 in deep and has a point load P at the third points…

A:

Q: A simply supported beam carrying floor joist shown in Figure is made of rectangular wood having a…

A: