A vessel, cylindrical in shape and closed at top and bottom, contains water upto a height of 80 cm. The diameter of the vessel is 20 cm and the height of the vessel is 120 cm. The vessel is rotated at a speed of 400 rpm about its vertical axis. What will be the height (in cm) of the paraboloid formed?

A vessel, cylindrical in shape and closed at top and bottom, contains water upto a height of 80 cm. The diameter of the vessel is 20 cm and the height of the vessel is 120 cm. The vessel is rotated at a speed of 400 rpm about its vertical axis. What will be the height (in cm) of the paraboloid formed?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A body floats half and submerged in a certain liquid (s.g. = 1.25) and has a weight of 500 kN. Determine Determine the minimum weight of the anchor weighing 23.54 kN/m³ that will require to submerge the body completely in Problem 4. L.S. Vu body -anchon gr.aghicaro2018
Civil engineering -Hydraulics
Civil Engineering In the figure below, calculate the seepage from the bottom of the pond and the head at the interface between the two materials? 8 m 3 m K=1x 105 m/s S, = 0.12 1m K=1x 10° m/s S=1 x 105 Om
In a hydraulic press, the ram has a diameter of 20 cm and the plunger 2 cm. The fluid is an oil of specific gravity 0.8. Calculate the mass that can be raised by placing a mass of 100 kg on the plunger: (i)When the plunger and the ram are on the same horizontal plane, and (ii)When the liquid level in the plunger is 0.5 m above that in the ram. What is the mechanical advantage of the press in cases (i) and (ii) above?
Question Certain fluid parameters are provided The inner cylinder, with a diameter of 20 cm, remains stationary, while the outer cylinder, with a diameter of 21 cm, holds the liquid up to a height of 30 cm. There is a 1.0 cm gap between the bottom of the two cylinders. By rotating the outer cylinder at a speed of 200 revolutions per minute (r.p.m.), the torsion meter attached to the inner cylinder registers a torque of 6.0 N-m. a. Determine the toque on the bottom in terms of b. Determine the toque on the surface in terms of ..... c. Determine method the viscosity of a liquid (N-sec/m^2)(Ans up to 2 decimal) μ (Ans up to 4 decimal) ..u.(Ans up to 4 decimal) using the rotating cylinder
Oil is filled within a tall cylindrical tank. A flat disk with a height of 1 cm and with a diameter of 5 cm is placed into the oil. There occurs a narrow spacing of 0.1 mm between the disk and the tank wall. Due to the forces acting on the disk, it moves downward, and after some time, the speed of the disk reaches a terminal velocity. Beyond this moment, measurements reveal that the disk moves 30 cm in 4 seconds. If the oil density is 600 kg/m3and the specific gravity of the disk is 1.5, determine the oil’s viscosity.
2-liter soda bottles do not have flat bottoms. A bottle can be approximated as a cylinder filled from the bottom up to 0.26-m high with a hemispherical space of 10-cm-diameter underneath. If you treat the soda as having the density of water, what is the force in N of the soda on the curved bottom of the soda bottle?
A large oil tank contains a circular gate with a diameter of 2 meters fixed to the inclined wall of the tank, as shown in Figure 2. The gate is installed on a column along its horizontal diameter, oil height 12 m above the column. Find the force needed to open the gate, if you know that the density of oil is 850. (Ixc=nR¹/4) V Ⓒ2m 12m Fig. 2