A very long copper rod 20 mm in diameter extends horizontally from a plane heated wall maintained at 100 °C. The surface of the rod is exposed to an air environment at 20 °C with convective heat transfer coefficient of 8.5 W/m² .K. Workout the heat loss if the thermal conductivity of copper is 400 W/m. K.

A very long copper rod 20 mm in diameter extends horizontally from a plane heated wall maintained at 100 °C. The surface of the rod is exposed to an air environment at 20 °C with convective heat transfer coefficient of 8.5 W/m² .K. Workout the heat loss if the thermal conductivity of copper is 400 W/m. K.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A two-layer 24 m² plane wall consists of a 250 mm thick inner concrete layer with thermal conductivity k, of 2 W/m K and a 80 mm thick outer insulation with k, of 0.04 W/m K. The temperatures of wall inner and outer surfaces are t, = 28°C and t3 =-9°C. Calculate (i) the rate of heat transfer and (ii) the temperature t, of the wall intermediate surface.
i need the answer quickly
The length of one side of a cube-shaped freezer cabinet is 11.8 m. your closetits base is perfectly insulated against heat transfer and the inner surface temperature is –5 °C, the outer surface temperatureand it is 59°C. To ensure that the thermal load of the cabinet is not less than 0.59 kWThe thickness of the styrofoam foam insulation (k=0.03 W/mK) to be applied to the upper and side surfacesWhat should be less?
I need the answer as soon as possible
In an experiment to measure the thermal conductivity of a plate of unknown material with area 1 m2 and thickness 0.1m, one of its surfaces is maintained at 100 °C and the other at 20 °C and a heat at the rate of 100 kW was supplied across it. Determine the thermal conductivity of the hot plate. Is the material metallic, non-metallic, or gas/liquid?
A pipe carrying hot gasses is insulated with a material having a thermal conductivity of 0.15 W/mK. The average local heat transfer coefficient by convection to the ambient air is 3 W/m K. The critical diameter of the pipe under 35. these conditions is (a) 100 mm (c) 160 mm (b) 130 mm (d) 200 mm
Homework problem for unsteady-state heat transfer Consider a product to be sterilized if its coldest location during heating reaches 115°C. Consider sterilization of potatoes where potatoes (4 cm diameter) is heated in steam at 121°C. Assume symmetrical heating of potatoes and the heat transfer coefficient between the steam and the potatoes is 20 W/m² K. The thermal diffusivity for potatoes is 1.5 × 107m²/s and the thermal conductivity is 0.4 W/m K. The potatoes are initially at 30°C. 1) Calculate the heating time needed for sterilization. 2) Calculate the temperature at the center of the potato after heating 1000 s and 2000 s. Plot how the temperature at the center changes with time t. 3) Calculate the temperature at the surface of the potato at 2000 s. Qualitatively plot how the temperature changes across the apple at t = 2000 s.
I need complete solutions and 4 decimal places in all solutions.
I need the answer as soon as possible
Plate glass 5 mm thick at 200°C is to be cooled from both sides using air at 40°C. If surface cracks are to be avoided, determine the maximum value of convective heat transfer coefficient. Material properties are density = 2500 kg/m3, specific heat 670 J/kgK. Thermal conductivity 0.744 W/mk. Also determine the time required in this to cool the plate to 80°C.
The thermal conductivity of a solid material can be determined using asetup similar to the one shown in the accompanying figure. The thermocouples are placed at 2.5 cm intervals in the known material (copper alloy, k - 52 w/m.k) and the unknown sample, as shown. The known material is heated on the top by a heating element, and the bottom surface of the sample is cooled by running water through the heat sink shown. Determine the thermal conductivity of the unknown sample for the set of data given in the accompanying table. Assume no heat loss to the surroundings and perfect thermal contact at the common interface of the sample and the copper.
A block with thickness 2.3cm, and conductivity k-4W/mK is heated such that its temperature at its top is T₁-191°C Above the block, air at temperature Tair 22°C is blowing across the top which has a surface area of 1m² with heat transfer coefficient of 26W/m²K. air & W/mK T₁ T₂ What is the thermal resistance from T₂ to T? Provide total thermal resistance answer in units of K/W and to 4-decimal places