A vertical wall 6 m high above the water table, retains a 20° soil slope, the retained soil has a unit weight of 18 kN/m³, the appropriate shear strength parameters are C = 0 and = 40°. The coefficient of active earth pressure to be used in estimating the active pressure acting on the wall is

A vertical wall 6 m high above the water table, retains a 20° soil slope, the retained soil has a unit weight of 18 kN/m³, the appropriate shear strength parameters are C = 0 and = 40°. The coefficient of active earth pressure to be used in estimating the active pressure acting on the wall is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An 8 m tall retaining wall holds cohesionless sand with a density and angle of internal friction of 1.85 Mg/m3 and 33°, respectively. If the surface of the backfill slopes upwards at 86° to the vertical, Use Rankine’s conditions to find the force per unit length of the wall and its location for (a) Active State (b) Passive State Please draw the pressure diagram neatly for both cases
A retaining wall supports a horizontal backfill that is composed of two types of soil. First layer: 5.64 meters high, Unit weight of 16.86 kN/m3, coefficient of active pressure of 0.281 Second layer: 5.42 meters high, Unit weight of 18.46 kN/m3, coefficient of active pressure of 0.304 Determine the distance of the total active force measured from the bottom of the wall. Round off to three decimal places. A Click Submit to complete this assessment. F2 FS F6 FB DIE 4 5 6 7 8 9 R Y G H K B LT V フコ因

Considering that the horizontal thrust from the back of a 5.5 m wide brick wall to the 1 m deep part of the wall is H = 55 kN a) Find the greatest stress in the base when b = 2 m.b) Find the width b so that there is a shrinkage zone at the base.(Note: unit weight of brick wall ỿ = 24 kN / m3 ) Answer: ϭmax=0,30 Mpa, b=2,23 m
Question 1: You are designing a retaining wall at the construction site. The friction angle of sand backfill is 28". Define the active lateral earth pressure coefficient based on Rankine's theory. Show your work and select the closest value: a) 0.30 b) 0.35 c) 0.40 d) 0.50
A gravity retaining wall retains 12 m of a backfill, y = 17.7 kN/m² = 25° with a uniform horizontal surface. Assume the wall interface to be vertical, determine the magni tude and point of application of the total active pressure. If the water table is a height of 6 m. how far do the magnitude and the point of application of active pressure changed? Please solve carefully and don't give wrong answers and box the final answers
The following figure shows a section of an anchored retaining wall embedded into a saturated stiff clay layer. The sand has a unit weight of = 18 kN/m³, c' = 0 kPa and o' = 34º. The clay has a unit weight of = 20 kN/m³, c₁ = 80 kPa and = 0°. A uniform pressure of 40 kPa is applied on the soil surface. The short term stability of the wall is considered in an undrained analysis. Use the Rankin's theory of lateral earth pressure to determine the active and passive horizontal stresses. You should apply the requirements of AS 4678 and the partial factors of safety method in estimation of soil pressures. Assume the soil is in-situ and use a structural classification factor of ₁ = 1. 3m 1m Water table 1.5m 40 kPa Not to Scale Sand Clay Ta
A thin clay layer passes through the soil at an angle of 30° behind an 8m high gravity retaining wall. A structure 5m wide, applying a uniform stress of 40kPa to the sandy soil, also acts on this section of soil as shown in Figure 3.1. The properties of the clay are ??=25???, ∅?=0, ?′=0 and ∅′=20°. The sandy soil properties are ?′=0, ∅′=35°, ????=16??/?2, ????=20??/?2, and between the sand and the wall the properties are ?′?=0 and ∅′?=30°. Assuming that failure occurs along the clay layer, use Coulomb’s method to calculate the horizontal force required from the wall in the short term to prevent slip.
A vertical retaining wall 8.8 meters high retains a horizontal backfill having the following properties: Void ratio = 0.64; Specific Gracvity = 2.64; Water Content = 28 %; Angle of internal Friction = 31°. Compute the location of the active force in meters from the bottom of the wall acting on it if the water table is 3.0 meters below the ground surface.
Q: For the retaining wall shown in the following figure, determine the force per unit length of the wall for Rankine's active state. Also find the location of the resultant. 3 m z 3 m y = 16 kN/m³ ' = 30° c' = 0 Groundwater table Y sat = 18 kN/m³ ' = 35° c' = 0
A level ground surface exists in an area where soil in the underlying stratum has a wet unit weight of 19 kN/m3. The vertical pressure at any depth represents the major principal stress. The vertical pressure (stress) is the product of the soil unit weight and depth. The lateral pressure at a corresponding depth is 0.45 times the vertical pressure and represents the minor principal stress. (a) Determine the principal stresses acting at a depth 4 m below the surface, and draw the Mohr’s circle for the condition. (b) What is the maximum shear stress acting at this depth?
Find the passive earth pressure coefficient. For a vertical retaining wall having a backfill of dry sand inclined at an angle of 20° from the horizontal