A vertical post AB is embedded in a concrete foundation and held at the top by two cables as shown in Figure Q3. The post is a hollow steel tube with Modulus of Elasticity of 200 GPa, outer diameter of 40 mm, and thickness 5 mm. The cables are tightened equally by unbuckles.  -State the type of joining for Rod AB - Determine the load allowable for rod AB if a factor of safety of 3.0. - Based on the Euler buckling in the plane of the figure is desired, analyses the requirement the maximum allowable tensile force Tallow in the cables.

Q: The column AB is connected to the frame through pin-joints as shown in Figure 1. There exists a…

A: Given  G = 40 KN/m Q = (LL) = 20 KN/m   d=depth= 198 mm  bf = flang width = 99 mm  tf = flang…

Q: Given the configuration in Figure 1, calculate the load that can be supported under the following…

A: GIVEN; Pin diameter =10 mm =0.01 m Ultimate strength σut = 195 MPa FOS =2 Strength of cable = 207.5…

Q: The frame shown in the figure is loaded as shown. (a) Draw the FBD for the frame. (b) Determine the…

A: The hinge at A gives the horizontal and vertical reaction The roller at E gives the horizontal…

Q: Calculate the critical load of a steel circular column for pinned-pinned boundary conditions using…

A:

Q: a. Two brass rods used as compression members, each of 3-m effective length with pin end, have the…

A: Given:Effective length of the rods, Le=3 mOuter diameter of circle, do=60mmInner diameter of circle,…

Q: PLEASE ANSWER NUMBER 3.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND…

A: Free Body Diagram: At Joint C;   At Joint C; FV = 0 PBC = 96 kN  => It is the member of BC   For…

Q: The AB bond must be made of a steel for which the normal stress limit is 450 MPa. Determine the…

A:

Q: calculate the maximal force F which can be applied to the couplin

A: fot solution refer below images.

Q: 15 in 05 im 24 in The machine link shown is subjected to an axial load P, as shown. The link is…

A:

Q: Urgent

A: Given:-

Q: An assembly of a structure is composed of two cable rods BD, CE, and bar member AC as shown in…

A: Given: The maximum load intensity, w1 = 35 kN/m The minimum load intensity, w2 = 10 kN/m The point…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2-…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: Current Attempt in Progress The pin-connected structure consists of two cold-rolled steel [E-31.000…

A:

Q: A rigid bar ABCD is pinned at end A and supported by two cables at points B and C. The cable at B…

A:

Q: 2. (a). Two steel plates are joined by bolts. Details are given below. Determine the load factor NL,…

A: given; (a)Sut=600MPaaxial load(P)=18000Ntensile stress area(At)=157mm2diameter of…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

A:

Q: A simple rigid structure ABC is to be built to hold load at Cas showa in Figure Q Suppoit AE is to…

A:

Q: 1: An aluminum alloy (E = 70 GPa) bar of circular cross section consists of uniform and pered…

A:

Q: ple: Determine the value of P, if the load W= 800 N.

A:

Q: Q2: A composite bar is made up two vertical rods of steel and copper each of length 2 m and diameter…

A: from the above figure given data is load is 15KN in the given question find out each load on the…

Q: me the maximum force P that can be supported by the truss as shown in Figure Q4, without caus to…

A:

Q: D F 4m E 3m 3m he pin-jointed frame work in the figure If a vertical concentrated load of 800KN…

A:

Q: 8. The figure shows a roof truss and the detail of the connection at joint B .Members BC and BE are…

A:

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

A: Given Data:- Side(s)  =0.1m = 3.93inch.......considering the unit as meters  Thickness (t) =0.01m =…

Q: A rectangular plate of width b-40 mm and thickness s 20 mm has a hole with a diameter d=8 mm in the…

A: Given:b=40 mms=20 mmd=8 mmF=15000 NFor dw=840=0.2;From the graph:Kf=2.5Stress developed without…

Q: 4. Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using…

A:

Q: The one end of a hollow square bar whose side is 10 in with 2 in thickness is under a tensile stress…

A: Given Data: The side of the hollow square bar is s = 10 in. The thickness of the hollow square bar…

Q: An L-2 steel link in a forging machine is pin connected to the forks at its ends as shown. Determine…

A:

Q: The A frame shown in the figure is attached to an overhead beam by 2 cap screws, each of which can…

A: To determine the appropriate screw for the given load and conditions, we need to follow several…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

A:

Q: cotter joints supports a load varying from 3000 kgf in compression to 3000 kgf in tension. The…

A:

Q: Determine the reactions at A and E if P = 500 N. What is the maximum value which P may have for…

A:

Q: ased on the yield stress rk out the allowable lo

A: A= 20x20= 400 mm2 Yield strength = 250 MPa F(s) = 4 Allowable stress = ? Working load =?

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

A: Given Data: The side of the hollow square bar is s =10.47 in. The thickness of the bar is t = 1.47…

Q: Question: 35 35 The one end of a hollow square bar whose side is (10 +) in with (1 +) in thickness…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.