A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the stress is limited to 5 MPa, which of the following most nearly gives the maximum height of water up to which the tank may be filled? Select the correct response:

A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the stress is limited to 5 MPa, which of the following most nearly gives the maximum height of water up to which the tank may be filled? Select the correct response:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A large pipe, called a penstock in a hydraulic work, is 1.5 m in diameter. It is composed of wooden…

Q: A cantilever beam, 80 mm wide by 230 mm high and 7 m long, carries a load that varies uniformly from…

A: Given: Cantilever beam 80mm wide, 230mm high, 7m long UNiform load varies from 0 to 1400N/m

Q: 4. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN.…

A: Given data in question Inside diameter Load Stress To find out Outside diameter

Q: A solid shaft transmits 300 kW at 100 rpm. If the shear stress is not to exceed 80 N/mm², what…

Q: A cantilever beam, 70 mm wide by 220 mm high and 8 m long, carries a load that varies uniformly from…

Q: A hollow metal tube with an inside diameter of 55 centimeters must carry a tensile load of 490 kN.…

Q: IS Smm. alculate the allowable internal pressure if the stress is limited to 40MP..

A: d=5m t=8mm

Q: mine the normal stress in a ball, which has an outside diamete d to a gage pressure of 66 kPa. er:0,…

Q: The ratio of diameters for a hollow steel tube is 0.10 which carry a load of 500 kN. If the…

A: stress - its the ratio of the applied force and the resisting area of the cross section of the…

Q: A tank in the shape of sphere is filled with fluid and then pressurized. The diameter of the tank is…

A: We will apply formula of hoop stress.

Q: A cantilever beam, 100 mm wide by 230 mm high and 8 m long, carries a load that varies uniformly…

Q: A tank in the shape of sphere is filled with fluid and then pressurized. The diameter of the tank is…

Q: A non-Newtonian fluid is flowing in a floor having height 5mm and with a free stream velocity of 0.5…

Q: A large uniform cylindrical steel rod of density ρ = 8.8 g/cm3 is 4.0 m long and has a diameter of…

A: Introduction : Normal stress : A normal stress is a stress that develops when an axial force is…

Q: tank in the shape of sphere is filled with fluid and then pressurized. The diameter of he tank is…

A: d=5.5ft t=0.335in stress=9525psi

Q: A cylindrical tank holding oxygen at 1,146 kPa pressure has an outside diameter of 430 mm and a wall…

Q: An upright cylindrical water tank having a diameter of 3 meters and a height of 6 meters is to be…

Q: A closely coiled helical spring of mean diameter 140 mm is made up of 12 mm diameter steel wire.…

A: GivenDiameter of helical spring D=140 mmRadius R=70 mmDiameter of steel wire which is used in spring…

Q: Q.6 A solid shaft is subjected to a bending moment of 500 Nm and a torque of 700 Nm. Calculate the…

A: given Bending moment M=500 NmTorque T=700 Nmpermissible normal stressσb=100 MPa

Q: Determine the normal stress in a ball, which has an outside diameter of 195 mm and a wall thickness…

Q: Problem 3.4 A hollow steel tube with an inside diameter of 150 mm must cany a tensile load of 450…

Q: A hollow metal tube with an inside diameter of 265 centimeters must carry a tensile load of 910kN.…

A: Di=2.65m P=910kN P=910000N

Q: A cantilever beam. 80 mm wide by 260 mm high and 8 m long. carries a load that varies uniformly from…

Q: Problem 2. The 200 mm diameter rod is subjected to 300 N and 500 N loads as shown in Figure 2.…

A: in the given beam both torque and bending moment both are acting so that torque - transverse load…

Q: .For a thick walled cylinder subjected to internal pressure only, mention the surface where the…

A: Stress is a different quantity than the amount of difficulty in the system and the stiffness of the…

Q: Calculate the minimum wall thickness (in) for a cylindrical vessel that is to carry a gas at a…

Q: Find the stress produced in cylindrical rod subjected to 22 KN having diameter of cylindrical rod is…

A: When a load is applied stress is produced . The nature of stress depend upon the load . If tensile…

Q: Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a pressure…

Q: A cantilever beam, 70 mm wide by 260 mm high and 8 m long, carries a load that varies uniformly from…

Q: A WATER TANK IS 8m IN DIAMETER AND 15m HIGH. IF THE TANK IS TO BE HALF FILLED, DETERMINE THE MINIMUM…

Q: A cantilever beam 80 mm wide by 260 mm high and 9 m long carries a lpad that varies uniformly from…

A: First find moment at 4m from free end . Use bending equation.

Q: 4. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN.…

A: Given, Inside diameter = 100 mm Allowable stress = 120 MPa Tensile load = 400 kN Outside diameter =?

Q: If the density of concrete i A concrete dam has the profile shown in Figure 2400 kg/m³ and that of…

A: Given data : Density if concrete = 2400 kg/m3 density of water = 1000 kg/m3 h = 15 m Determine the…

Q: A hollow steel tube with an inside diameter of 60 mm must carry an axial tensile load of 360 kN.…

Q: Jer beam, 70 mm wiIdi and 9 m long, carries iformly from zero at t N/m at the wall. Dete

Q: A cantilever beam, 80 mm wide by 280 mm high and 7 m long, carries a load that varies uniformly from…

A: Given: Cantilever beam dimensions Uniformly varying load To find: Magnitude of stress.…

Q: A 4m long rectangular sectioned rigid solid pole with 30mm thickness is fixed to a wall in one end…

Q: For a thick walled cylinder subjected to internal pressure only, mention the surface where the…

A: Since the question number to be solved is not specified, the solution for Question No.01 is as…

Concept explainers

Pressure and Stress

Question

A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm.
If the stress is limited to 5 MPa, which of the following most nearly gives the maximum height of water up to which the tank may be filled?
Select the correct response.
O 8.16 m
3.68 m
7.36 m
4.08 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cantilever beam, 80 mm wide by 240 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1500 N/m at the wall. Determine the magnitude of the stress in a fiber 70 mm from the top of the beam at a section 6 m from the free end. Answer must be in MPa.
Determine the maximum tensile stress in the following beam:
A cantilever beam, 100 mm wide by 270 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1400 N/m at the wall. Determine the magnitude of the stress in a fiber 80 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
A cantilever beam, 90 mm wide by 280 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1300 N/m at the wall. Determine the magnitude of the stress in a fiber 60 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
A wooden beam 100 mm by 200 mm , supported as shown in figure below, carries a load F. what is the largest safe value of F if the maximum stress is not exceed 10 MPa ? 100mm 200 mm
Question-8, A cylindrical pressure vessel is1200 mm in diameter. It is made of rolled mild steel plate. The vessel is subjected to an internal pressure of 2 N/mmt. If the material yields at 200 N/mmt, what should be the minimum safe thickness of the plate, based on Maximum Principal Stress Theory?(FOS-1.5)
A cylindrical tank holding oxygen at 1,523 kPa pressure has an outside diameter of 432 mm and a wall thickness of 11 mm. Compute the longitudinal stress (in MPa) in the wall of the cylinder.
4. A cylindrical tank 8.3m in diameter is H m high. If the tank is filled with water, determine the maximum height H if the tank plating is 17mm thick and if the material is capable of the allowable stress of 35MPa.
Exercise 2.8.3. Determine the maximum and minimum stress intensities set up in steel flat section 150 mm wide and 20 mm thick subjected to a pull of 200 kN, which is off the geometrical axis by 4 mm in the plane which bisects the thickness.
A cantilever beam, 80 mm wide by 220 mm high and 7 m long, carries a load that varies uniformly from zero at the free end to 1400 N/m at the wall. Determine the magnitude of the stress in a fiber 90 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
QUIZ 1 NORMAL STRESS 1. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine the outside diameter (in mm) of the tube if the stress is limited to 120 MN/m².