A cylindrical shell made of mild steel plate of 100 cmdiameter is to be subjected to an internal pressure of 10kg/em?. If the m aterial yields at 2000 kg/em2, assumingfactor of safety as four and using maximum principal stresstheory, thickness of the plate will beA.5 mmB.10 mmC.15 mmD. 20 m m

Given data- A cylindrical shell-Diameter of steel plate (D) = 100 cmInternal pressure (P) = 10…

A cylindrical shell made of mild steel plate of 100 cm diameter is to be subjected to an internal pressure of 10 kg/em2. If the material yields at 2000 kg/cm?, assuming factor of safety as four and using maximum principal stress theory, thickness of the plate will be A. 5 mm B. 10 mm C. 15 mm D. 20 mm

A cylindrical shell made of mild steel plate of 100 cm diameter is to be subjected to an internal pressure of 10 kg/em2. If the material yields at 2000 kg/cm?, assuming factor of safety as four and using maximum principal stress theory, thickness of the plate will be A. 5 mm B. 10 mm C. 15 mm D. 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Compute the combine stress on a solid round bar with a diameter of 3 cm. The load of 75,000 KN is…

Q: A metal bar of length 100mm is inserted between two rigid supports and its temperature is increased…

A: Given data- Length of the bar L=100 mmIncrease in temperature∆T=10oCCoefficient of thermal expansion…

Q: Example 2.36. A railway is laid so that there is no stress in the rails at 8°C. Calculate (a) the…

A: Given :

Q: The internal diameter of a thin cylinder is 200 mm and it is subjected to internal pressure of 15…

Q: A circular tube of outer diameter D is slipped over a 40-mm-diameter solid cylinder. The tube and…

Q: The material of a rubber balloon has a Poisson's ratio of 0.5. If uniform pressure is applied to…

A: Given Data; Poisson's Ratio = (μ) = 0.5 Uniform pressure applied to blow to balloon. To Determine…

Q: A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to an internal pressure…

Q: A metal bar of length 100mm is inserted between two rigid supports and its temperature is increased…

Q: Answer

Q: Q.6 A solid shaft is subjected to a bending moment of 500 Nm and a torque of 700 Nm. Calculate the…

A: given Bending moment M=500 NmTorque T=700 Nmpermissible normal stressσb=100 MPa

Q: A body is subjected to stresses as shown in the figure given below. 90 MPa 35 MPa 145 MPa The FOS as…

Q: Theory of Failure Question 1: The uniaxial yield stress of a material is 866 MPa. According to von…

A: Yield stress- σy=866 MPa, It is needed to find the shear yield stress as per the Von-mises…

Q: If Surface tension for a Jet form is 0.05 N/mm and diameter of Jet is 0.3 Cm then pressure will be?

A: given- surface tensionσ=0.05 N/mmdiameter of jetd=0.3 cm=3 mm

Q: A solid rotor of a turbine is 0.6 m diameter at the blade ring. It is keyed to a 50 mm diameter…

A: Given : Diameter of rotor = 0.6 m Diameter of shaft = 50 mm Min. thickness = 9.5 mm Uniform Stress =…

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 42 mm. The…

A: problem 1Givendiameter of the pressure vessel d=450 mm=0.45 mthickness t=42 mm=0.042 m,longitudinal…

Q: A thin cylinder of internal diameter 1 m and thickness 0.02 m contains a gas. The tensile stress in…

A: A thin cylinder- Internal diameter d = 1 m, Thickness t = 0.02 m, Tensile stress σ=100 MPa. To Find-…

Q: QUESTION 1 a) A bar 30 mm in diameter and 80 mm in length is subjected to a tensile load 100KN. The…

Q: ter of the hoop formed by the band i se the temperature of the hoop, so t

Q: A cylindrical tank holding oxygen at 2.091 kPa pressure has an outside diameter of 409 mm and a wall…

Q: Problem 1: Given the axially-loaded compound shaft, determine the axial stress developed in each…

Q: Question: Principal stresses at a point are 80 N/mm² and 40 N/mm2 both tensile. The yield stress in…

A: Given- Principal stresses- σ1=80 N/mm2,σ2=40 N/mm2, Yield stress- σy=200 N/mm2, It is needed to find…

Q: A 25m steel rod with diameter of 20 mm is secured between rigid supports at both ends. If there is…

A: Stress due to temperature difference can be calculated with the help of the following equation, σ =…

Q: True stress-strain behaviour of a metal is given by the flow curve equation o = 1750 €0.37 where o…

Q: A cylindrical shell of 100 cm diameter made of mild steel plate is to be subjected to an internal…

A: given-1 diameter d=100 cminternal pressure p=10 kg/cm2stress σy=200 kg/cm2FOS=4

Q: An 8-mm thick steel tank has an outside diameter of 600 mm. It is subjected to an internal pressure…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

A cylindrical shell made of mild steel plate of 100 cm
diameter is to be subjected to an internal pressure of 10
kg/em?. If the m aterial yields at 2000 kg/em2, assuming
factor of safety as four and using maximum principal stress
theory, thickness of the plate will be
A.
5 mm
B.
10 mm
C.
15 mm
D. 20 m m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw/Illustrate all axial, shear and bearing forces.
two decimaal places
A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by 50°C. If rod is allowed to expand by 14 mm, what will be the stress induced in rod? Take E = 200 GPa and α = 12 x 10-6/°C.
A solid cube of side 1 m is kept at a room temperature of 32°C. The coefficient of linear therma expansion of the cube material is 1 x 105/°C and the bulk modulus is 200 GPa. If the cube is constrained all around and heated uniformly to 42°C, then the magnitude of volumetric (mean) stress (in MPa) induced due to heating is و او را
Solid mechanics
1.31 A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of 15°C. If the rod is heated uniformly to 115°C, determine the length and the diameter of this rod to the nearest micron at the new temperature if the linear coefficient of thermal expansion of steel is 12.5 x 10° m/m/°C. Is there a stress on the rod at 115°C?