A cylindrical pressure vessel isfabricated from steel platingthat has a thickness of 42 mm.The diameter of the pressurevessel is 450 mm and its lengthis 2.0 m. Determine themaximum internal pressure thatcan be applied if the longitudinalstress is limited to 140 MPa, andthe circumferential stress islimited to 60 MPa. * A cylindrical steel pressurevessel 400 mm in diameter witha wall thickness of 20 mm, issubjected to an internalpressure of 5 MN/m^2. (a)Determine the safe stressbetween the tangential andlongitudinal sections in thesteel. (b) To what value may theinternal pressure be increased ifthe stress in the steel is limitedto 120 MPa? (c) If the internalpressure were increased untilthe vessel burst, sketch the typeof fracture that would occur.

problem 1Givendiameter of the pressure vessel d=450 mm=0.45 mthickness t=42 mm=0.042 m,longitudinal…

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 42 mm. The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 42 mm. The diameter of the pressure vessel is 450 mm and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 11 of 12 - / 1 Current Attempt in Progress A 33 mm by 33 mm square ABCD (i.e., a = 33 mm)…

A: In this problem, we are given a square that is deformed into a rhombus due to the application of a…

Q: 1. An axial compressive load of 50 tons is applied to a metal bar of square section 2 in. by 2 in.…

A: Hjh

Q: cer is flowing in a pipe of 200 cm diameter un the pipe wall is 0.75 cm. The tensile stress in th

Q: A 0.2 mm thick tape goes over a frictionless pulley of 25 mm diameter as shown in figure. If E of…

Q: A spherical balloon is filled with a gas. The outer diameter of the balloon is 12 in, and the…

Q: The rigid platform shown has negligible mass and rests on two steel bars, each 250 mm long. The…

Q: AN 8 MM THICK CYLINDRICAL STEEL TANK HAS AN OUTSIDE DIAMETER OF 600 MM AND A LENGTH OF 3 M. (a) WHEN…

A: Given Thickness 8mm Diameter 600mm Assume unit weight of water 10kn/m^3

Q: Problem 3 The tube shown below has a uniform wall thickness of 12 mm. For the loading given,…

A: We have to determine the value of stress at point A and B in the given figure according to the given…

Q: The kinematic viscosity of the oil filled between two concentric vertical 150 mm long cylinders is…

A: Given data in question Length 150 mm Diameter 0.2 m Kinematic viscosity Specific gravity of oil…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

A cylindrical pressure vessel is
fabricated from steel plating
that has a thickness of 42 mm.
The diameter of the pressure
vessel is 450 mm and its length
is 2.0 m. Determine the
maximum internal pressure that
can be applied if the longitudinal
stress is limited to 140 MPa, and
the circumferential stress is
limited to 60 MPa. *

A cylindrical steel pressure
vessel 400 mm in diameter with
a wall thickness of 20 mm, is
subjected to an internal
pressure of 5 MN/m^2. (a)
Determine the safe stress
between the tangential and
longitudinal sections in the
steel. (b) To what value may the
internal pressure be increased if
the stress in the steel is limited
to 120 MPa? (c) If the internal
pressure were increased until
the vessel burst, sketch the type
of fracture that would occur.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 solution

VIEW

Step 2

VIEW

Step 3 (b) increased value of the pressure

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An 8-mm thick steel tank has an outside diameter of 600 mm. It is internal pressure of 2.40 MPa. Determine the maximum subjected to stress in the tank. an
Determine the maximum tensile stress in the following beam:
Problem : Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hooke's Law (E) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters?b) Check whether the pressure vessel is safe or not? Given data: - The yield strength of the pressure vessel is σy = 250 MPa.The inner diameter of the vessel is d = 2 m.The pressure acting in the vessel is P = 10 Atm.The longitudinal stress is σL = 200 MPa.Hooke's Law (E) = 150 MPaThe radial stress is σR = -50 MPa.
A strain gage is mounted at an angle of 30° with respect to the longitudinal axis of the cylindrical pressure. The pressure vessel is fabricated from aluminum [E = 10,000 ksi; v=0.33], and it has an inside diameter of 54 in. and a wall thickness of 1.00 in. If the internal pressure in the cylinder is 706 psi, determine the maximum shear strain on the outer surface of the cylinder. Ο Ο Ο Ο 1049 με 1714 με 1600 με 1268 με 1167 με
A cylindrical tank holding oxygen at 1,523 kPa pressure has an outside diameter of 432 mm and a wall thickness of 11 mm. Compute the longitudinal stress (in MPa) in the wall of the cylinder.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion? Given data: -The yield strength of the pressure vessel is σy = 250 MPa.The inner diameter of the vessel is d = 2 m.The pressure acting in the vessel is P = 10 Atm.The longitudinal Stress is σL = 200 MPa.Hoop Stress σθ = 150 MPaThe Radial Stress is σR = -50 MPa.
A high-strength steel [E = 188 GPa] tube having an outside diameter of 67 mm and a wall thickness of 4.1 mm is bent into a circular curve having a 42-m radius of curvature. Determine the maximum magnitude of the bending stress max developed in the tube. Answer: Omax = i MPa.
Q..c,.