A vertical cylinder of 60 mm diameter is penetrated by another cylinder of 40 mm diamet the axis of which is parallel to both the HP and the VP. The axis of two cylinders is 5 m part Draw projections showing curves of intersection

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: 1-) b. 1+j 1 Evaluate a. 1+j

A: Ans(a)  j2=-1 Divide by 1-j both sides 1-j1+j×1-j1-j (1-j)21-j2=1+j2-2j2=-2j2=-j

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: The object shows the center of the whole is three inches from the left surface and one inch from the…

A: we have to determine what kind of dimensions are used in the hole

Q: I'm playing a game of pool with by brother; he's stripes. At some point, I notice I have a…

A: V = 6 oz = 0.17 gd = 2.25 inches = 0.057 me = 0.95  "coefficient of restitution" "coefficient of…

Q: Draft and annotate the below sketch using AutoCAD Note: colour the hatching lines with different…

A:

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: What is the period in seconds?

A: To determine: The time period for the swing, where it takes approximately 2 seconds to reach on side…

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: 2. From the given figure below, solve for the bar Y from the reference line. (choose the nearest…

A:

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: Write the types of keys and sketch freehand of them with dimensions and equations.

A: A key is a machine element that is fitted in the axial direction with the mating parts in pulleys…

Q: a) Solve for ox'. Express your answer in kilopounds per square inch to three significant figures. b)…

A:

Q: Find the number of rotations of wheel 3 in rotations per minute (rpm) wile the load A is moving down…

A:

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: N

A: Given: To find: Correct rotation code

Q: 20.00 40.00 60.00 FRONT 60.00 00'0 20.00 00'0

A: If straight lines are drawn from various points on the contour of an object to meet a plane, the…

Q: 0 = 0° A

A:

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Required Front view, Top view and Right Hand Side view are drawn using First Angle Method of…

Q: Q4 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 1:1.

A: Required Front view, Top view and side view are drawn using first angle method of projections.

Q: Can you please help me draw the Isometric illustrations from the given orthographic drawing? I will…

A: Note: As per policy, we can solve the first one from multiple questions. Please resubmit the…

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What does the expression VB/A mean? O A. O B. Absolute velocity of point B. OC. Velocity of point B…

A: Relative velocity: The rate of change in relative position of one object with respect to another…

Q: sketch a rube goldberg machine using the following operations dominoes falling, rolling ball, pulley…

A: A rube goldberg machine is to be drawn considering the operations such as falling, rolling ball,…

Q: Draw the Isometric drawing of the given orthographic projections below. Use drawing scale to fit the…

A:

Q: 20 R3 Which tools that can be used to :3 draw the following shape in .AutoCAD 37 23 43 R3 dimension,…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.