A vertical curve is needed to join to tangents; G₁=2% and G2-5%. Assuming the worst case scenario for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the comfort criteria. The design speed is 50 mph. Response Feedback: G2-G₁ is positive, therefore a sag curve. A=3 Lmin=AV²146.5

A vertical curve is needed to join to tangents; G₁=2% and G2-5%. Assuming the worst case scenario for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the comfort criteria. The design speed is 50 mph. Response Feedback: G2-G₁ is positive, therefore a sag curve. A=3 Lmin=AV²146.5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A car is traveling up a 1.25% grade of a crest curve with a design speed of 65 mph. The descending grade is -2.75%. What is the required length of curve for minimum proper stopping sight distance? AASHTO Minimum Stopping Sight Distances on Level Roadways (based on braking distance) stopping sight distance design speed (mph) braking distance on level (ft) design (ft) (m) brake reaction distance calculated (km/h) (ft) (m) (m) (ft) (m) (20) (30) (40) (50) (60) (70) (80) (90) (100) (110) (120) (130) (13.9) (20.9) (27.8) (34.8) (41.7) (48.7) (55.6) (62.6) (69.5) (76.5) (83.4) (90.4) (4.6) (10.3) (18.4) (28.7) (41.3) (56.2) (73.4) (92.9) (114.7) (138.8) (165.2) (193.8) (18.5) (31.2) (46.2) (63.5) (83.0) (104.9) (129.0) (155.5) (184.2) (215.3) (248.6) (284.2) (20) (35) (50) (65) (85) (105) (130) (160) (185) (220) (250) (285) 15 55.1 21.6 76.7 80 20 73.5 38.4 111.9 115 25 91.9 60.0 151.9 155 30 110.3 86.4 196.7 200 35 128.6 117.6 246.2 250 40 147.0 153.6 300.6 305 359.8 423.8 45 165.4 194.4…
Please answer question below and include all steps on how you got the answer
An equal-tangent vertical curve connects a +3.2 % and a -1.1 % grade. The PVI is at station 100+20 and elevation 950 ft and the PVT is at station 105+20. Answer the following 5 questions Question 3 to Question 7. The station of the PVC is at: sta 93+20 sta 95+20 sta 97+20 sta 99+20 sta 105+20
Design a vertical curve (i.e., Determine length of the curve as well as station and elevation of the vertical curve's PVC and PVT) with the given PVI (station and elevation given the figure below) to go through a future intersection location at the point at which the vertical curve is flat. Report the vertical curve's design speed to the nearest 5 miles per hour. PVC Future Intersection Station = 100+00 G1 = -2.6% PVT PVI G2 = 1.0% Station = 99+00 Elevation = 228 ft %3|
QUESTION 3 A vertical curve is needed to join to tangents; G₁-5% and G₂-2%. Assuming the worst case scenario for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the safety criteria. The design speed is 50 mph.
Highway problem.
this is one question split by parts a and b.
A vertical curve is needed to join to tangents; G1=1% and G2=4%. Assuming a level grade (0%) for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the safety criteria. The design speed is 60 mph.
There is a need for conducting a design check for a horizontal curve (flat terrain) for an intermediate speed highway in rural Victoria. Given the design speed is 80kmph and superelevation is 7%. The provided horizontal curve radius is 700m. Would the designed curve radius will be sufficient to attain the superelevation? If not, what would be the correct radius for horizontal curve? When suggesting a new radius please check and make sure that the provide superelevation is higher (>7%) than required.
A vertical curve is needed to join to tangents; G₁=1% and G2-4%. Assuming a level grade (0%) for braking, and the AASHTO recommended values for deceleration and perception-reaction time, calculate the minimum length of curve (ft) needed to satisfy the safety criteria. The design speed is 60 mph. Response Feedback: G2-G₁ is positive, therefore a sag curve. A=3 SSD(0%)=565.5 ft If you assume SL, Lmin-340 ft. SSD is greater than Lmin. The assumption is good.