There is a need for conducting a design check for a horizontal curve (flat terrain) for an intermediate speed highway in rural Victoria. Given the design speed is 80kmph and superelevation is 7%. The provided horizontal curve radius is 700m. Would the designed curve radius will be sufficient to attain the superelevation? If not, what would be the correct radius for horizontal curve? When suggesting a new radius please check and make sure that the provide superelevation is higher (>7%) than required

Q: A large grain elevator is located 40 ft from the centerline of a two- lane highway, which has 12-ft…

A: Combines harvest grain from the field and transfer it to a grain cart or directly into a truck…

Q: PROBLEM #1) An existing highway with bearing of N 20deg E to be connected to another highway, with…

A:

Q: II. PROBLEMS 1) Module 12 - Horizontal Curves An existing highway with bearing of N20°E is to be…

A:

Q: A horizontal curve in an urban area is being designed for 40 mph. If there is a maximum radius of…

A:

Q: A highway reconstruction project is being undertaken to reduce accident rates. The reconstruction…

A: Given data - v = 50 mph L = 800 ft x = 3+52 ft = 352 ft Offset (Y) = 3 ft Find out - if the existing…

Q: Suppose that a horizontal curve on a two-lane two-way highway has a radius of 200.000m. The lane…

A: Given Data :  Radius of curve (R)= 200m Lane width (w) = 3.3m SSD = 120m

Q: You are designing a vertical sag curve joining a -3% grade to a +2% grade. The design speed is 60…

A:

Q: Two vertical parabolic curves have been connected to form a roadway by three gradients: -5.30 %,…

A: Highway engineering is a significant subject in structural designing. It remembers the investigation…

Q: 3. What is AASHTO's recommended perception reaction time (s)?

A: Reference : AASHTO, American Association of State Highway and Transportation To determine : AASHTO…

Q: There is a need for conducting a design check for a horizontal curve (flat terrain) for an…

A: Design speed (V) = 80 kmph Superelevation provided (e) = 7% or 0.07Radius (R) = 700 m

Q: What do you understand by "adequate visibility" and "passenger comfort and safety" as applied in…

A: Adequate visibility refers to the provision for adequate sight distance at any section of the curve.…

Q: comply with the SSD. 6. A grade g₁ of +3.50% intersects grade g₂ of -2.50% and an equal-tangent…

A:

Q: you

A: Given  V=80kmph L=900 g1=2.0% g2=-1.5%

Q: A rural highway has a radius of 150m. Max Superetevation = 6% Safe side friction factor = 0.17.…

A:

Q: 11. Two vertical parabolic curves have been connected to form a roadway by three gradients: -5.30 %,…

A: Highway engineering is a significant subject in structural designing. It remembers the investigation…

Q: 14. The ruling minimum radius of horizontal curve of a national highway in pljain terrain for a…

A: Given data : Velocity (V)=100 kmphSuperelevation (e)=0.07Friction (f)=0.15

Q: nly answer question 6

A: Stopping Sight Distance is the minimum distance that must be available in front of driver so that he…

Q: Q5: Calculate the superelevation, maximum permissible speed, and transition length for a 3⁰ curve on…

A:

Q: There is a need for conducting a design check for a horizontal curve (flat terrain) for an…

A: Design speed (V) = 80 kmph Superelevation provided (e) = 7% or 0.07Radius (R) = 683 m

Q: While designing a highway, a gradient of 1 in 20 is provided. A horizontal curve of radius 200 m is…

A:

Q: A horizontal curve on a two-lane highway is designed with a 610-m radius, 3.5-m lanes, and 80 kph…

A:

Q: The maximum super-elevation to be provided on a road curve is 1 in 15. If the rate of change of…

A: Note- It is required to solve only the first problem.Maximum super-elevation e=1/15,Rate of change…

Q: A sag vertical curve is to be designed to join a -4% grade to a +2% grade. If the design speed is 45…

A:

Q: 5. What is the assumed height (ft) of the driver's eye for passenger cars?

A: Explanation :  The driver's eye distance/ height of driver's eye for passanger cars is the vertical…

Q: A section of a two-lane, two-way highway (2 @ 3.5 m) is to be designed with a circular curve. Sta.…

A: Width of the single lane = 3.5mnumber of lane = 2Sta. Pl at 200+ 100.000Design speed = 60kph…

Q: A 2-lane (12 ft wide lanes) with a horizontal and a crest vertical curve is reportedly designed for…

A: A horizontal curve that gives a transition between two tangent strips of roadway, allowing a vehicle…

Q: a 2250 ft length for a vertical curve was selected by a designer which connected a (- 4%) grade with…

A: Given  n1 = -7%  n2 = +4% v = 60mi/h =97 km/h Reaction time of driver, t = 11.5 s

Q: Q1) The project speed is 100 km/h on a divided state road with a vertical curve. The driver's…

A: Designed speed (V) = 100 kmphReaction time (t) =  2 secFriction coefficient (f) = 0.4Elevation and…

Q: PROBLEM 1 A SIMPLE CURVE HAVING A CENTRAL ANGLE OF 40 DEGREES AND EXTERNAL DISTANCE OF 20M CONNECTS…

A: Given that, Central angle = 40° External distance of two tangents connection is 20M

Q: A vertical curve was designed in 2005 for SSD requirements at a design speed of 120 km/h to connect…

A: Answer Based on Autralian guidelines, SSD is calculated using SSD = 0.278*v*t+v2254*f Where SSD =…

Q: A highway is designed at 100 km/h design speed. A 245 m equal tangent crest vertical curve exists at…

A:

Q: ye height of 2.4m, a passenger car driver eye height of 1.1m, and an object height of 0.2m,…

A:

Q: A grade of vertical curve can expressed as be O O O OC O A-In terms of percent O D-Both A and B C-In…

A:

Q: 3. A 3° horizontal curve is proposed to begin at STA 12+35 and end at STA 34+35. The design speed of…

A:

Q: A horizontal curve is being designed for a new four-lane roadway with 11-ft lanes. The PT is located…

A: Given;Road has four lane of 11 ft.PT is located at station 105+20Design speed = 45 mph =66…

Q: The minimum simple curve radius you recommended for a highway with design speed (96) Km/hr , super…

A: Given: Design speed v = 96 kmph  Super elevation e = 5.5% = 0.055 Friction coefficient f = 0.11…