a) USING NO MORE THAN FIVE UNIT DELAYS, draw a linear sequential cir-cuit (LSC) that takes as input an arbitrary polynomial input a(x), andproduces as output:(1+ a² + a* + ) a(x)b) USING NO MORE THAN SEVEN UNIT DELAYS, draw a linear sequentialcircuit (LSC) that takes as input an arbitrary polynomial input a(r), andproduces as output:a(x)1+ x2 + r4 + r³ + x7

Linear sequential circuit , y(x) = ax+x2+a(x)+x4a(x)+x5a(x) y(x) = (1+x2+x4+x5)a(x) NUmberr of…

a) USING NO MORE THAN FIVE UNIT DELAYS, draw a linear sequential cir- cuit (LSC) that takes as input an arbitrary polynomial input a(x), and produces as output: (1+a² +* + ") a(x) b) USING NO MORE THAN SEVEN UNIT DELAYS, draw a linear sequential circuit (LSC) that takes as input an arbitrary polynomial input a(r), and produces as output: a(x) 1+ x2 + r4 + r5 + x7

a) USING NO MORE THAN FIVE UNIT DELAYS, draw a linear sequential cir- cuit (LSC) that takes as input an arbitrary polynomial input a(x), and produces as output: (1+a² +* + ") a(x) b) USING NO MORE THAN SEVEN UNIT DELAYS, draw a linear sequential circuit (LSC) that takes as input an arbitrary polynomial input a(r), and produces as output: a(x) 1+ x2 + r4 + r5 + x7

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the effect of increasing and decreasing proportional gain to the system output. Discuss the effect of increasing and decreasing derivative gain to the system output. Discuss the effect of increasing and decreasing the integral gain to the system output. 4. Discuss some advantages of using Simulink over the MATLAB codes I WANT THE ANSWER FOR THIS QUESTION WITHOUT PLAGIARISM
3 A. We have a 4-bit DAC with Vref = 3.3V and an input voltage of Vs = 2.05V. Draw a diagram illustrating the conversion process of a successive approximation ADC. Label the x-axis conversion step and the y-axis Digital Number(DN). What digital number (DN) will be returned by the DAC within the SAR ADC? 3 B. You have purchased an 8-bit R-2R digital to analog converter to control the joint position on a robot arm (which is proportional to the input voltage). a). The DAC shows an output voltage of 0.49 V when the binary value 00011001 is applied. What is the full-scale analog output range of this DAC in volts? b). What voltage does the DAC output with a binary value of 10101010 applied? c). If the joint rotates 10.0 degrees/V applied, what is the minimum joint rotation increment you can achieve with this DAC?
(b) Figure Q1(b) shows the step response for a second-order system. Find its peak time and percentage of overshoot. Hence, obtain its transfer function. 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0. 6 10 12 14 16 18 20 22 24 Time (s) Figure Q1(b) Response
Hundred percent accuracy needed in the order to get positive feedback please provide me correctly solution and get the thumbs up By hand solution needed only
RC Or For the given circuit, the switched is closed for a long time and the switched is opened at t=0. R=5 kQ, C=47 µF and 1=4 mA given. Calculate the capacitor voltage at t= 0.6 seconds V (t=0.6) = ? (Your result must be in Volts) Only give numeric results. (If you found 0.18 Volts, write down 0.18) 十

please just answer part e
a) A buck converter has an input of 100 V, output current of 10 A with L= 250 µH and C = 100 µF. The duty cycle is 40% with switching frequency of 10 kHz. The circuit operates with continuous inductor current at threshold 4.8 A. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state, determine the following. i. The output voltage. ii. The inductor ripple current. iii. The maximum and minimum value of the inductor current.
please show the step claerly
A voltage-controlled oscillator (VCO) is an oscillator that oscillates at a constant frequency and is controlled by an external bias voltage. A VCO's output is a frequency, and its input is a bias or control signal, which can be either dc or ac voltage. Which of the following assertions is a TRUE statement? Select your answer. The output frequency changes or deviates accordingly when ac voltage is applied to the VCO input. The output frequency changes or deviates appropriately when a square voltage is delivered to the VCO input. The output frequency changes or deviates appropriately when a DC voltage is delivered to the VcO input. The output frequency fluctuates or deviates accordingly when a dc or slowly shifting ac voltage is introduced to the VCO input.
Digital e
Determine the output of the DAC in Figure (a) if the waveforms representing a sequence of 4-bit numbers in Figure (b) are applied to the inputs. Input DO is the least significant bit (LSB). 200 k Do o W 23 45 6789 1011 12 1314 15 100 k) +5 V 10 k Do +5 V D +5 V D, o 50 kfl D; o M D2 +5 V 25 kfl D, o W (a) (b)
I need an expert handwritten solution to the question