A uniform circular thin rod of radius 10 in. is attached to a pin at C and to the cable AB. Find the centroid C(x, y) with respect to the axis as shown in the figure below. y B A O C X

Q: TOPIC: TORSION I. Write ALWAYS TRUE if Hhe At ate ment ia true for all Rtuation 2f not , Write F…

A:

Q: In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each…

A:

Q: ynami

A: given: what is second law of thermo dynamic?

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A:

Q: White cast iron cannot be heat treated Select one: .True .False

A:

Q: Whoop- ニフ P:?

A:

Q: you! A round vertical steel tank has an inside diameter of 3 m and is 6.5 m in height. It contains…

A: Given:d=3 mh=6.5 mρ=850 Kg/m3σallow=25 MPa

Q: Part A, B, C Solved below,  asking solution for part D, E, F, G

A: In case of determining shear force and bending moment for the beams with udl or uvl, it is advisable…

Q: 100 KN 20 KN/m 10 m need NF, SF and BM diagram ? detailed answer in a basic way

A: It is required draw NF,SF AND BM Diagram

Q: What will be the occerelalion at point L if theuniform KL bor is left horigontal. 2m Support…

A: Given, The mass of the bar, m=25 kg The length of the bar, L=4 m

Q: Introduction to stress analysis Problem: Calculate the critical design loads applied to the piston…

A: Piston is a reciprocating part of an internal combustion engine which reciprocate with in the…

Q: 1- Design and sketch the form for 7.5 ft high and 1 ft thick wall using 5/8" B-B plyform Class I (4…

A: Given:- h=7.5 ftt=1 ft5/8" B-B plyform Class I (4 ft x 8 ft sheets)2 x 4 s4s Douglas Fir Larch No.2…

Q: Q4/ - B- State the purpose of case hardening of steel?

A: Case-hardening is also known as surface hardening, in this process the surface of a metal object is…

Q: Handwrite

A:

Q: Q3. Explain the hot working process with a help of diagram

A: Hot Working process is explained below.

Q: Handwrite

A: Detailed explanation:"I appreciate your dedication in conducting a comprehensive homework…

Q: Question 5 If the clay is OC, pre-consolidation pressure, Pc=200 kPa, Cc=0.1, Cr=0.020, eo=0.9,…

A: Clay is OC-Preconsolidation pressure Pc=200 kPGCc=0.1cR=0.020cB=0.9 assueme,rW=9.8 kn/mSurehatge…

Q: Q3. What is "Hardness" and how it can

A: ◆The hardness is defined as, "the ability of the material that can resist indentation or scratch or…

Q: Q4/ Give the reason or reasons for (any four) of the following ( materials and applications) 1. Zinc…

A: Engineering materials are a class of materials that are utilised to build man-made structures and…

Q: Choose the suitable method for foaming metal. 1. Mix and add directly blowing agent into the molten…

A: following are the outlines of the suitable process for metal foaming

Q: Qus - The state of two dimensional stress acting on a concrete lamina consists of a direct tensile…

A: Given data  State of stress  Normal stress = 6 MPa  Shear stress = 4 MPa  Find the maximum tensile…

Q: Compute the amount of energy necessary to convert 20L of water at 15oC to saturated steam at 100oC.

A: Solution is attached below:

Q: 12- To calculate Brinell hardness number (BHN) used the equations *

A: The Brinell hardness number is a number which is used to indicate the strength of any material in…

Q: Draw a typical blast furnace in details and label the major components ?

A: Iron Blast Furnace It is a type of blast furnace and the function of this furnace is to reduce…

Q: What material and corresponding stresses is best for HP shape?

A:

Q: kindly differentiate the canning methods of process in boiling water bath and using autoclave with…

A: Canning is the process in which foods are placed in cans and jars and heating them to a specified…

Q: ow many hyl of steam at 1600k and 0.20mpa can be safely placed in a tetrahedron conrainter with edge…

A:

Q: A thin gas cylinder with an internal radius of 100 The maximum permissible working stress is mm is…

A: Given, Radius of cylinder = r = 100 mm Diameter of cylinder = d = 2r = 200 mm Internal pressure in…

Q: wrench size 18 cm, the lever force to be applied to the key and the tightening force of the bolt.

A:

Q: A hydraulic punch press is capable of delivering 2,000kPa pressure on its platen from its 250mm…

A: Given: A hydraulic punch press is capable of delivering 2,000kPa pressure on its platen from its…

Q: Compressive stress is an example for stress Select one: O a. Direct O b. Indirect O .Combined O d.…

A:

Q: 1 Demi e ARCndD

A:

Q: to k3 find ra) the global stiffness matrix.

A: First locate the nodes

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.