(a)Two vertical cylindrical tanks of 3.00- meter and 2.00-meter diameter containing waterare joined at their base by a pipe of diameter 0.05 meter. This pipe is short enough to be treatedas an orifice with a co-efficient of discharge of 0.58. The 3.00-meter tank initially has a level= 6 =2.00 meter higher than the other. Calculate how long it will take for the level difference tohalf.

Answered: Image /qna-images/answer/321ab674-faea-4f9d-8374-2554ae61f476.jpg

Answered: (a) Two vertical cylindrical tanks of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Kindly answer all the parts correctly and in good handwriting (i.e. handwritten) for an upvote..Thank you
В4. An orifice meter with orifice area 1039 mm2 is inserted in a pipe of area 2078 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 60 cm of mercury. Find the rate of flow of oil of sp. gr. 0.9 when the co-efficient of discharge of the orifice meter = 0.52. Head of water (in m) The discharge of water through pipe (in Litres/sec)
Shown in the figure below is a pipe system (commecial steel pipes) having a given centerline geometry is to be used to transfer oil from Tank A to Tank B at a rate of 1.70 cubic meter per minute. Minor losses from the pipeline are due to 2 pcs-90o elbows (K = 0.5) ; Contraction (K = 0.05) and Expansion (K=1). If the oil has a density of 801.3 kilogram per cubic meter and viscosity of 2.394x10 -2 kilogram per meter per second, the diameter of the pipe in millimeter is Blank 1 mm. *Express your answers in whole significant figure without decimal value and without unit*
In the figure below, assume the pipe from B to C has a diameter of 4-inches, (f = 0.035), and length of 18-feet. The pipe from DE is 187-feet, has a diameter of 4-inches and friction factor of 0.035. The Az = 69-feet. The elevation of C is 14-feet above the lower water surface. If the pressure head @ C is to be no less than (-) 20 feet, and the pump has 63% efficiency, what horsepower must be supplied to the pump in order to convey flow through the system? (Kent = 0.8) Assume a submerged exit. Az
A vertical circular tank that is 1.5 m high, has sloping sides. The tank is 50 m and 30 m in the top and bottom diameters respectively. Discharge takes place through a triangular orifice situated at the bottom of the tank. The orifice has a base of 0.8 m long, 0.5 m below its vertex. If the tank is originally full of water, what time is required to empty the tank? Take discharge coefficient as 0.63
On a trip to the beach (Patm 1 atm or 101.3 kPa), a car runs out of gasoline and it is necessary to siphon gasoline from a Good Samaritan's car. The siphon is a hose with a small diameter and to start the action it is necessary to insert one end into the tank full of gasoline, fill the hose with it through suction and then put the other end in a can that is placed under the tank level. The difference in pressure between point 1 (on the free surface of the gasoline in the tank) and point 2 (at the outlet of the tube) causes the liquid to flow from the highest elevation to the lowest. In this case, point 2 is located 0.75 m below point 1, and point 3 is 2 m above 1. The siphon diameter is 4 mm and friction losses in it must be ruled out. Determine: a) theminimum time to bring 4 L of gasoline from the tank to the can and b) the pressure at point 3. The density of the gasoline is 750 kg / m3.
As shown in figure below, oil can be siphoned from a tank using a flexible hose, provided that the end of the hose at Point B, is below the free surface in the tank at Point A. The maximum elevation of the hose is at Point C. Oil is being siphoned from the tank through a constant-diameter hose. The end of the siphon at Point B is 6.71 meters below the oil top surface level of the tank at Point A. If the gauge pressure at Point C is 90.257 KPa and the density of oil is 890 fraction numerator k g over denominator m cubed end fraction , the vertical distance between Point C and Point B in meters is

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS