A two-phase induction motor, 4 kW, quadrupole, 250 V and 50 Hz, has the following specifications: R = 0.50 , X,m = 30 , R = 10 x2 = 42 , Xm = 802 The motor is powered by an unbalanced two-phase source with voltages of 250 and 220. If the machine works with a slip of 0.1, it is desirable: A) Direct and inverse components of stator phase current and effective phase current values B) Mechanical power produced

A two-phase induction motor, 4 kW, quadrupole, 250 V and 50 Hz, has the following specifications: R = 0.50 , X,m = 30 , R = 10 x2 = 42 , Xm = 802 The motor is powered by an unbalanced two-phase source with voltages of 250 and 220. If the machine works with a slip of 0.1, it is desirable: A) Direct and inverse components of stator phase current and effective phase current values B) Mechanical power produced

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

( read values &Solve Carefully and Box final answer ) Hint : Enter your answer to the 2nd nearest decimal place.
Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
Electrical circuits: determing the following.
In this System your primary element is sending 1v - 5v to your controller and our controller is sending 4mA - 20mA to your final Element. 1) The Primary Element is sending 2.8v. Your controller is reading 2.8v. The Controller sends 5.2mA to the Final Element but nothing changes in your Process Variable. What is wrong? Controller Final Element Transmitter Wire 2) The Primary Element is sending 12v. Your controller is reading 12v. The Controller sends 0mA to the Final Element. What is wrong? Controller Final Element Transmitter Wire 3) the Primary Element is sending 3.4v. Your controller is reading 0v. The Control is not making changes when necessary, what is wrong? Controller Final Element Transmitter Wire
Write down at least three reasons which cause difference between R1 (R2) and R = Vmes/imes values in the below table?
What is the difference between active and passive loads
W1 A 1 IL Tr1 AC Supply V V w2 12 Tr2 use double range voltmeter Fig.(1)
VDD- 10 Velt 106 ID2 I07 Assume the following: (a) M1 and M2 are matched (b) = 0 for all MOSFETS (c) L identical for all FETS. (d) ID2 = 50 µA. (e) W1=W2=W3=W6=W8 (f) W4=W5=2 x W2 (g) W7=3 x W8 (h) Except for W/L ratios establishëd by the photolithography design, the fabrication process is the same for all FETS. Pay attention to sign convéntions! Provide values for: ID3 ID4 ID7 ID5 = drain circuit for M5! (Trick question. Careful-look at the
Q1: For the circuits shown in figures. If the temperature has changed from 25°C to 65°C. find AIc. Ic=1.5mA at 25°C. Vcc +20v 25°C 65°C 47k 33.9k 55 70 Ico InA 16nA 12knS VBE 0.6 0.5 S1.2k
Explain this diagram
Kindly provide .Soln .
Note:Leave an image of the exercise in Spanish, so that it is better understood. In the other image, is the final answer, to verify that it is correct. :)