A turbine is supplied with 0.6 m³/s of water from a 0.3m diameter pipe; the discharge pipe has a 0.4m diameter. Determine the pressure drop across the turbine if it delivers 60 kilowatts of energy. (Hint: use conservation of mass and then conservation of energy) Wout = 60 kilowatt Din = 0.3 m Dout = 0.4 m Qin = 0.6 m3/s Turbine

A turbine is supplied with 0.6 m³/s of water from a 0.3m diameter pipe; the discharge pipe has a 0.4m diameter. Determine the pressure drop across the turbine if it delivers 60 kilowatts of energy. (Hint: use conservation of mass and then conservation of energy) Wout = 60 kilowatt Din = 0.3 m Dout = 0.4 m Qin = 0.6 m3/s Turbine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is pumped from a pond to a tank by using a pump at a rate of 55 dm/s through a 50.4-mm-diameter steel pipe. The total length of the pipe is 95 m, and the viscosity of water is 1 mm2/s. Calculate the power required in the pump to maintain the discharge. Refer to Figure Q1 to include all losses in your calculation. (2) 20 m Gate Valve Pump (Fully Opened) 2 m Globe Valve (75% Opened) Figure Q1
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
= constant Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. Z شكر الكائر 2B ADA=400 mm PA 29.43 N/cm #28 m ZA 28 Dg= 400 mm Pe = 22.563 N/cm ZB = 30 m DATUM LINE
I am having trouble with this problem.
2. A pipe 120 mm bore diameter carries water with a head of 3 m. The pipe descends 12 m in altitude and reduces to 80 mm bore diameter. The pressure head at this point is 13 m. The density is 1000 kg/m3. Assuming no losses, determine i. The velocity in the small pipe (7 m/s) ii. The volume flow rate. (35 dm³/s)
help!
Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
Hi. Kindly assist with this Fluid Mechanics question.Please answer correctly and show all the steps