A transformer rated at a maximum of 25kVA supplies a 12kW load at power factor 0.60 lagging. a) What percent of the transformer rating does this load represent? b) How many kW in additional load may be added at unity power factor before the transformer exceeds its rated kVA? c) Draw the power triangle before and after the additional load. d) If the additional load has a power factor of 0.866 leading, how many kVA may be added without exceeding the transformer rating?

A transformer rated at a maximum of 25kVA supplies a 12kW load at power factor 0.60 lagging. a) What percent of the transformer rating does this load represent? b) How many kW in additional load may be added at unity power factor before the transformer exceeds its rated kVA? c) Draw the power triangle before and after the additional load. d) If the additional load has a power factor of 0.866 leading, how many kVA may be added without exceeding the transformer rating?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Voltage divider bias Please select one: a. requires fewer components than all other methods b. can be essentially independent of ß_dc c. it is not widely used d. cannot be independent of ß_dc
In which of the following wind energy conversion system, guy wire may be required? O a. Vertical axis wind turbines Ob. Horizontal axis wind turbines O c. Up wind turbines O d. Down wind turbines
UP/DOWN CLK Qo Q₁ Q₂ Q4 (UP) (DOWN) _____ (UP) (DOWN) 山 In
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
True or False: Industrial safety requires to use of the lockout tags when you do not maintain or repair any machine. Select one: O True O False
Direction: Must carefully read the direction. You must Answer no.1 to no. 5. Identification only which the appropriate/correct answer is in the parenthesis. Choose correct answer in parenthesis in each question. No need to explain each answer. Provide a correct answer to each question. Zoom in the picture in order to see it clearly. Thank you in advance.
can you do question iii please?
Reaming tool is a single point cutting tool. Select one: True False
Find v(t)
SOLVE THE FOLLOWING. SHOW COMPLETE SOLUTION, CIRCUIT TRANSFORMATION, RESISTANCE COMBINATION.FIX CALCULATOR TO 3 DECIMAL PLACES. BOX FINAL ANSWER. • 1. Determine the equivalent impedance and the equivalent admittance. 2n -j4n Zea jion -jsn
I need answer within 20 minutes please
1. Define the cabling procedure in 3 sentences.2. What have you learned in making the cabling procedure?