Assignment 1: Please draw the wiring connections.Name:FROM METERNo. Matriks:CeilingLLampFanNSWITCHRCCBMCBMCBМСВFUSEC6C20C32commoncommonRegulatorL2 way switchintermediate2 way switchswitchEcommon1-way switchRadialRadialRingRing

The given diagram is, To draw the wiring connections.

Assignment 1: Please draw the wiring connections. FROM METER LN N L L N SWITCH RCCB FUSE N L L N - N 0 Radial Name: No. Matriks: MCB MCB MCB C6 C20 C32 B Radial E common 2 way switch XII Ring intermediate 0 ■ - switch E U Ring Lamp Al common 2 way switch E N Ceiling Fan O common Regulator 1-way switch

Assignment 1: Please draw the wiring connections. FROM METER LN N L L N SWITCH RCCB FUSE N L L N - N 0 Radial Name: No. Matriks: MCB MCB MCB C6 C20 C32 B Radial E common 2 way switch XII Ring intermediate 0 ■ - switch E U Ring Lamp Al common 2 way switch E N Ceiling Fan O common Regulator 1-way switch

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

E2(V) 120V Test Open-circuit Short- circuit Primary 12(A) .29A 2A P2(W) 8.78W 13.4W 6.85V E1(V) P1(W) 7.69W 13.14W Test Open-circuit Short- circuit 11(A) .62A SA 48V 2.83V Normal 12 at E1 11 P1 E2 12 P2 120V 50.6V 48.42V 48.8V 49.33V 182A 4A 6A 815A 1A 1.22A 142A .2 4.75A 237.4W 56.5W 120.3V 1.31A 1.77A 2.28A 2.73A 3.26А 3.74A 119.6V 119.8V 120.6V 119.4V 120.6V 120.1V 119.9V 120.3V 219.1W 48.3W 72.39W 98.3W 120.1W 146.9W .4 81.2W 108.2W 130.5W 159.2W 184W 209.2W 237.5W .8 49.1V 1.2 1.4 49.83V 49.91V 50.1V 50.55V 170W 193.6W 219.1W 238.1W 1.6 4.23A 1.616A 1.8 4.74A 1.82A 2.0 50.3V 5.18A 258.3W 119.1V 2A 1) Calculate the turns ratio from the transformer primary/secondary voltage ratinga a= Using the open-circuit data at the primary and the short-circuit data at the secondary, calculate the four transformer parameters (to 3 significant figures) and fill in the following table. Parameter Rel Value(ohm) Xel Rc1 Xm1 Using the open-circuit data at the secondary and the short-circuit data at…
Which manufacturing method is used to manufacture tiles? A. Slip casting/ Glipgietwerk B. Injection molding/ Spuitvorming C. Tape casting/ Bandgietwerk D. Extrusion/ Ekstrusie
Q2: Solve the following. Show COMPLETE/ DETAILED solution, resistor combination and circuit transformation. Box final answer. Fix calculator to 4 decimal places.pls do not use nodal analysis or source transformation.
Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
How do I convert the following per unit voltages to actual voltage?
Refer to figure 2. Calculate fault current
4. The maximum current passing through device is 125 mA. Find the instantaneous current when e=225^0 a. -125 mA b. -176.7767 mA C. -62.5 mA d. -88.3883 mA
If load sets are in parallel and inside each load set the lamps glow a. Few bright b. Dim C. none of them d. Bright
i need a code and diagram to make circuit arduino uno with these sensors MQ_7 gas sensor with (buzzer 4_8v DC) Dht11 flame detection sensor digital with (buzzer 4 - 8v Dc) hw 596 pressure alarm all these sensors show on Icd 20*4 i2c thanks
SOLVE IMMEDIATELY PLEASE PLEASE
The system is unstable if all the values in the first column of the Routh table are negative. TRUE OR FALSE
Q3/ For the below cct find (V1, V2, 1, & Ix) 1A 2A 2. Ix