A transformer has an open circuit voltage of 253 volts. A tap-changing device operates when the regulationfalls below 7% The load voltage at which the tap-changer operates will beO 244.44236.45O 161.15O 126.50A 4 pole, 230V, DC shunt motor develops an output power of 16 kW If Ra 0.05 ohms, and Rsh = 90 ohms,the armature current is

Given : Transformer has open circuit voltage of 253 volts.

A transformer has an open circuit voltage of 253 volts. A tap-changing device operates when the regulation falls below 7%. The load voltage at which the tap-changer operates will be V. 244.44 O 236.45 O 161.15 O 126.50 A 4 pole, 230V, DC shunt motor develops an output power of 16 kW, If Ra 0.05 ohms, and Rsh = 90 ohms, the armature current is

A transformer has an open circuit voltage of 253 volts. A tap-changing device operates when the regulation falls below 7%. The load voltage at which the tap-changer operates will be V. 244.44 O 236.45 O 161.15 O 126.50 A 4 pole, 230V, DC shunt motor develops an output power of 16 kW, If Ra 0.05 ohms, and Rsh = 90 ohms, the armature current is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The suitability of oscilloscopes for voltage measurement and DC display.
The total copper loss in an induction machine is found to be 1.5KW if the stator resistance is 0.6 Q. The stator current is O 50A O 100A O 28.87A O 57.74A Find the torque developed in an induction machine rotating at 1446rpm if the power developed is 5kw. O a. 33.02 O b. 66.04 O c. 0.03 O d. 103.73
The torque developed by a dc series motor is 16 N-m when drawing 23 A. If the current is doubled, the torque developed becomes N-m.
Can you solve the question ?
In a three-phase induction motor the maximum torque occurs at 20% slip and the equivalent resistance of the secondary is 0.04Ω per phase. Find the equivalent load resistance and the load voltage and the load current. Output power is 20 kW.
please provide good solution
Is this armature winding a progressive or a retro-progressive winding? W N Select one: 2 B 4' O a. Both O b. Progressive OC. Neither O d. Retro-progressive B S
Q4 A 11 kV, 500 MVA alternator is connected to a slow C.B. through a bus-bar. Determine the three ratings of the C.B, the average RRRV, and the oscillation frequency knowing that it reaches the peak re-striking voltage with 100 µs time.
q10
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 240 V (RMS), 50 Hz. The delay angles of both thyristors are set to 45 degrees. The maximum RMS and average current ratings of the thyristor are equal to: Select one: O a. 33.94A and 21.6A O b. None of these O c. 24A and 10.8A O d. 48A and 26.09A Clear my choice
A 600 V series motor takes 120 A and operates at 900 rpm when the load is80 HP. If the effective circuit resistance is 0.20 ohm, calculate the HPoutput of the motor when the current drops to 90 A. assuming that the fluxis reduced by 20 %. [Ans. 49.86 HP]