A transformer has 800 turns on its primary winding and 160 turns on the secondary. The output is 150 kva at 2300 volts. Determine (a) the ratio of transformation, (b) the rated primary voltage, (c) the full load secondary current, and (d) the full load primary current, neglecting the no-load component.

A transformer has 800 turns on its primary winding and 160 turns on the secondary. The output is 150 kva at 2300 volts. Determine (a) the ratio of transformation, (b) the rated primary voltage, (c) the full load secondary current, and (d) the full load primary current, neglecting the no-load component.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuits are 200,400 volts, respectively, at a frequency of 50 Hz The primary no-load current at voltage 200 equals 0.7 amps and pulp losses equal to 70 watts Primary resistance and reactance 3.2 , 1.25 In order, the reactance of the resistance and the coil 0.6 , 0.7 Then draw the equivalent circle, explaining the values
Select the correct statement for step down transformer. a. Primary number turns = Secondary number turns b. Primary number turns Secondary number turns d. Secondary number turns = 0
Core losses of a single phase 440/240 V, 24 kVA, 50 Hz transformer is 750 W. Maximum efficiency of the transformer is 90% at 15 kVA load and a certain power factor. Find the efficiency of the transformer at the same power factor and full load.
How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?
The required no-load voltage ratio in a 150 kVA single-phase 50 Hz core-type, two-winding transformer is 5000/250 V. Calculate the load kVA for maximum efficiency. The full-load I2R loss is 1800 W and the core loss is 1500 W. Round your answer off to the nearest whole number
Find the elements of the equivalent circuit attributed to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuit are 200 volts and 400 volts, respectively, with a frequency of 50 Hz. The primary no-load current at the voltage of 200 volts is 0.7 amperes and the loss of the core is equal to 70 watts. The resistance and reactance of the primary are 3.2 ohms and 1.25 ohms, respectively. The resistance and reactance of the secondary are 0.6 ohm and 0.07 ohm, respectively. Draw the equivalent circle, showing the values of its elements.
1) A 12 kVA, 4400V/230V, 50 Hz single-phase transformer has 150 secondary turns. Determine (a) the primary and secondary current,(b) the number of primary turns, and (c) the maximum value of the flux.
A 3.5 kV / 120V, 50 Hz, single phase transformer is to have an approximate e.m.f per turn of 33V and operate with a maximum flux density of 1.35T. Determine, (a) The number of primary and secondary turns. (b) The cross sectional area of the core.
b) The parameters of the transformer equivalent circuit are given bellow, Primary =1290. Secondary winding turns =130. The resistance of the primary winding =0.2 O. The resistance of the secondary winding =0.06 N. The leakage reactance of the primary winding =1.47 Q. The leakage reactance of the secondary winding =0.07 Q. using the above parameter values, referred to the primary winding, determine (a) Equivalent resistance, (b) Equivalent reactance, (c) Equivalent impedance and (d) The phase angle of the impedance.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
2- Proved that a resistance of (R¡ )in primary is equivalent to (R1 K’ )in secondary.? 3- A 40-kVA, 3,300/240-V, 50 Hz, 1-phase transformer has 660 turns on the primary. Determine (a) the number of turns on the secondary (b) the maximum value of flux in the core (c) the approximate value of primary and secondary full-load currents. Internal drops in the windings are to be ignored.