A trailer truck crossing a 10-m span circular beam ( D = 400 mm ) has axle loads of 7 kN, 9 kN, and 16 kN separated respectively by distances of 2 m and 5 m. Calculate the maximum bending stress and transverse stress developed in the beam. 7 kN -2 m 9 KN 5 m 16 kN. 10 m

A trailer truck crossing a 10-m span circular beam ( D = 400 mm ) has axle loads of 7 kN, 9 kN, and 16 kN separated respectively by distances of 2 m and 5 m. Calculate the maximum bending stress and transverse stress developed in the beam. 7 kN -2 m 9 KN 5 m 16 kN. 10 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 2: A 4.5-meter-long reinforced concrete beam supports a dead load of 20 KN/m, including self-weight, and a live load of 35 KN/m. The steel coating is 75mm thick. fc' = 28 MPa and fy = 415 MPa were used. 1. What is the greatest moment caused by the calculated loads? 2. If p=0.50pmax and d=1.5b, what should the bea'm width be? 3. What is the total steel area required?
A simple beam of length L = 5 m carries a uniform load of intensity q = 5.8 kN/m and a concentrated load 22.5 kN (see figure). P = 22.5 kN| 1.5 m q = 5.8 kN/m L= 5 m- The 1-1 and 2-2 axes are labeled on the cross section below. (a) Assuming oallow = 114 MPa, calculate the required section modulus S (in mm³). (At this point, disregard the weight of the beam.) mm3 Select the most economical wide-flange beam (W shape) from this table, and recalculate s (in mm), taking into account the weight of the beam. Select a new beam if necessary. mm3 H
A roadway sign that weighs Py = 6 kN is supported by a structural pipe with an outside diameter of 335 mm and a wall thickness of 12.0 mm. Wind pressure on the sign creates a resultant force of P₂ = 21 kN, acting as shown. Using length dimensions of a = 5.2 m and b = 6.6 m, determine (a) the normal and shear stresses at point H. (b) the normal and shear stresses at point K. P₂ Py N b H y K a x
For the beam with the given section and subjected to the loading shown below, determine the maximum axial stress. 10 kN 3 kN/m 100 mm 200 mm 15 m 1.5 m 2.2 m
A simply supported beam with a width of 150mm and a depth of 250mm is 3m long. It carries a uniformly distributed load of 6 kN/m throughout its span and a concentrated load of 15 kN at a point 2m form the left support. Determine the maximum bending stress (MPa) developed in the beam.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28 and fy is 420. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam
A uniformly distributed load of 4 kN/m, 6 m long crosses a girder 24 m long. What is the maximum bending moment at a section 8 m from the free end?
A rectangular beam 400 mm deep and 300 mm wide is simply supported over a span of 4 m. If the bending stress in the beam is not to exceed 120 MPa then the value of uniformly distributed load that the beam can carry is. kN/m. m
A cantilever beam of span 12 m carries a triangular load that varies linearly from zero at the free end to 360 N/m at the fixed end. In addition, a 1000-N upward vertical load acts at the free end of the beam. What magnitude of a uniformly distributed load must be added throughout the span of the beam so that there is no flexural stress at the fixed end of the beam, in kN/m? choices: 33.27 0.0333 0.0467 46.67
A roadway sign weighs 7.4 kN and is supported by a structural pipe that has an outside diameter of 160 mm and a wall thickness of 11.5 mm. The resultant force of the wind pressure acting on the sign is 13 kN, as shown. Assume a = 8.7 m, b = 4.1 m, P₂ = 13 kN, and Py = 7.4 kN. (a) Determine the normal and shear stresses OH, Txy at point H. (b) Determine the normal and shear stresses OK, Tyzk at point K. Answers: OH = TxyH = OK = Tyzk = y HK i i i P₂ i b a MPa. MPa. MPa. MPa.
A 4-m span wooden beam with rectangular section simply supports a uniform distributed loading of w=15.85 in KN/m. One support (roller) is located 1-m from the left end and the other support (hinged) is located at the right end of the span. The allowable bending stress is 9 MPa and the allowable shearing stress is 0.60 MPa. Neglect the beam weight and assume the beam to have a depth to width ratio of 1.50. What is the width of the beam so that it will not exceed the allowable bending stress?
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The f'c is 28 and the fy is 420. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam