A thin steel tire is shrunk on to a locomotive wheel of 1.2 m diameter. Find the internal diameter of the tire if after shrinking on, the hoop stress in the tire is 100 MPa. Assume E=200kN/mm2. Also find the least temperature to which the tire must be heated above that of the wheel before it could be slipped on. The coefficient of linear expansion for the tire is 6.5×10–6 per °C.

Q: ild steel rod having a stress of 50 Mpa and having a diameter of 20 mm  What is the force applied

A: Given:Stress, σ=50 MPadiameter, d=20 mm

Q: A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is…

A:

Q: nodulus of dulüs öf the mate the thermal strain, e

A: GIVEN:L=2md=50mmT1=20CT2=350CE=80GPa

Q: Find FOS as per goodman's realtion

A: Given data; Thin spherical pressure vessel having following data;   σ1=σ2=pr2t   (where;p=8, r=100…

Q: Given: A part is made of ductile material and subjected to principal stresses 01, 02,03. statically…

A: For solution refer below images.

Q: 1. A measure of the sample's resistance against hydrostatic compression is 2. Biot hypothesized that…

A: Given Statement To find Appropriate phrase

Q: What will be the cross-sectional area in mm² of the prismatical bar of length 5 mm and weight per…

A:

Q: A closed thin walled cylindrical vessel has a diameter D of 780 mm, a wall thickness t of 3.5 mm and…

A:

Q: walled vessels is assumed to apply? ssure found in part (a), compute the s

A:

Q: Q.4 Calculate the elastic constant G and K of a cylindrical bar of diameter 30 mm and of length L m…

A:

Q: MPa . Assumin H/m² and Poisso hange in diamet

A: Given data  Dia of pressure vessel =650 mm Internal pressure = 14.7 Modulus of elasticity = 200 GPa…

Q: A copper cylinder 150mm outside diameter has walls 25mm thick. End plates are stayed by a 25mm…

A:

Q: 3.4 3.2 P' D. 3.0 2.8 2.6 2.4 K 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.1 0.3 0.4 0.5 0.6 0.7 0.2 2r/D

A: Calculated failure load (P)of the panel. And calculated average stress far away from the hole.

Q: A copper rod of diameter 10 mm and length 4 m has a tensile force of 5 kN applied on it . Modulus of…

A:

Q: The axis of a tree has the following data, the diameter d= 40mm and the length is L= 0.9m and it…

A:

Q: Consider a plane of area 30 m^2 in a bar. The bar is subjected to tensile force of 5 kN. Calculate…

A: Given data: The area of the plane of the bar is A=30 m2 The tensile force in the bar is P=5 kN The…

Q: Find the maximum stress in the belt.

A: Given data; T1-T2= 100 Nb= 1cm =0.01 mt =0.5 cm=0.005 mθ= 1700=170×π180=2.967 radv= 1000…

Q: A close coiled helical spring that is made of a material with a shear modulus of 150 GPa, has a wire…

A:

Q: nal pressure, find wh able stresses for the

A:

Q: What will be the cross-sectional area in mm² of the prismatical bar of length 5 mm and weight per…

A:

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: With the force P appliced on a member, the stress distributions at different cross sections are…

A:

Q: An elastic rubber sphere of radius 20mm is pressed upon a rigid sphere of radius 50mm. The Young’s…

A:

Q: mm. The compliance of the UTM is constant and is given by 5 x 108 m/N. The strain at failure in the…

A: Given data;   Sample of length (L)=100 mm=0.1 m and this is loaded in tension until failureload=…

Q: A plat spiral spring is made of 6 mm wide.and 2.5 mm thick wire andis 250 cm long. Assuming the…

A: Given data: width of spring = 6 mm Thickness of wire = 2.5 mm length = 250 cm Maximum stress = 840…

Q: 9.7 (B). A thin-walled steel cylinder is subjected to an internal fluid pressure of 21 bar (2.1…

A:

Q: A steelbar having a diameter of 0.5 in is fixed at both ends and it is subjected to a tensile force…

A: Given:Diameter of the steel bar, d=0.5 inTensile force, F=1200 lbInitial temperature, Ti=70°FThermal…

Q: As shown in Fig, there is a gap between the aluminum bar and the rigid slab that is supported by two…

A: Given data as per question Area of copper rod =500 mm2 Area of aluminium rod =400 mm2 we know that…

Q: A steel disk with a 150 mm outer diameter is to be press fit to a hollow steel tube whose outer…

A:

Q: A thin-walled closed cylinder (radius r of 400 mm; wall thickness t of 20 mm), is simultaneously…

A: Solution: Given Data: r = 400 mm t = 20 mm P = 1.2 MPa T = 100 kN-m FOS = 2.8

Q: compression force of 50 N applied on the round bar of 500 mm diameter,  Calculate the stress…

A: Given:compressive force, F=50 Ndiameter of the round bar, d=500 mm or 0.5 m

Q: A steel circular tube is subjected to torsion by torques T applied at the ends as shown below. The…

A: This problem is related to the torsion of the shaft. torsion, when the twisting moment is applied to…

Q: Q1. Prove that the minimum thickness of a spherical shell which can withstand the internal pressure…

A:

Q: A one mm diameter steel wire is wounded around a copper tube with external and internal diameters of…

A: Given: The diameter of wore, d = 1 mm The external diameter of tube, Do = 140 mm The internal…

Q: A circular tube of aluminum is subjected to torsion by torques T applied at both end. The bar 0.5m…

A:

Q: st internal pressure, find w allowable stresses for the y are reached simultaneo

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.