A thin, light wire is wrapped around the rim of a wheel, as shown in (Figure 1). The wheel rotates about a stationary horizontal axle that passes through the center of the wheel. The wheel has radius 0.190 m and moment of inertia for rotation about the axle of 0.470 kg m. A small block with mass 0.350 kg is suspended from the free end of the wire. When the system is released from rest, the block descends with constant acceleration. The bearings in the wheel at the axle are rusty, so friction there does -7,50 J of work as the block descends 3.70 m. Part A What is the magnitude of the angular velocity of the wheel after the block has descended 3.70 m? Express your answer in radians per second. Πνα ΑΣφ rad/s Submit Request Answer

A thin, light wire is wrapped around the rim of a wheel, as shown in (Figure 1). The wheel rotates about a stationary horizontal axle that passes through the center of the wheel. The wheel has radius 0.190 m and moment of inertia for rotation about the axle of 0.470 kg m. A small block with mass 0.350 kg is suspended from the free end of the wire. When the system is released from rest, the block descends with constant acceleration. The bearings in the wheel at the axle are rusty, so friction there does -7,50 J of work as the block descends 3.70 m. Part A What is the magnitude of the angular velocity of the wheel after the block has descended 3.70 m? Express your answer in radians per second. Πνα ΑΣφ rad/s Submit Request Answer

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

what is the correct answer?
A spool of thread consists of a cylinder of radius R, = 4.2 cm with end caps of radius R, = 10.8 cm as depicted in the end view shown in the figure below. The mass of the spool, including the thread, is m = 180 g. The spool is placed on a rough, horizontal surface so that it rolls without slipping when a force T = 0.450 N acting to the right is applied to the free end of the thread. For the moment of inertia treat the spool as being a solid cylinder of radius R,, as the extended edges are thin and therefore light. \R2 (a) What is the acceleration of the spool? Take positive to be to the right. |m/s² (b) Determine the direction of the force of friction. O to the left O to the right O straight up O straight down
A weight of mass 1.60 kg is suspended by a string wrapped around a pulley wheel, which consists of a solid disk of mass 4.87 kg and radius 0.540 m. The system is released from rest. Over what vertical distance does the hanging mass move in 3.0 seconds? Ignore friction and drag forces, and assume that the string does not slip. Image size: S M L Max m MR
A block of mass m1 = 1.55 kg and a block of mass m, = 6.25 kg are connected by a massless string over a pulley in the shape of a solid disk having radius R = 0.250 m and mass M = 10.0 kg. The fixed, wedge-shaped ramp makes an angle of 0 = 30.0° as shown in the figure. The coefficient of kinetic friction is 0.360 for both blocks. М, R m1 (a) Draw force diagrams of both blocks and of the pulley. Choose FileNo file chosen This answer has not been graded yet. (b) Determine. the acceleration of the two blocks. (Enter the magnitude of the acceleration.) Enter a number. uation describing the angular acceleration of the pulley and the acceleration of the blocks? m/s2 (c) Determine the tensions in the string on both sides of the pulley. left of the pulley N right of the pulley N
A pulley with moment of inertia I = 0.75 kg-m² and radius R = 15 cm is mounted on a wall. A light string is wrapped around the pulley with a mass m = 2.0 kg attached to the end. The pulley rotates as the mass falls. Use Newton's second law to calculate the acceleration of the mass. Check that your formula gives the expected behavior when I →0. => To help get started, the free body diagrams m and the pulley is shown below. T m Write down Newton's second law for each diagram. Use (and explain) the relationship R a = RO TIL R T
An electric motor turns a flywheel through a drive belt that joins a pulley on the motor and a pulley that is rigidly attached to the flywheel as shown in figure. The flywheel is a solid disk with a mass of 80.0 kg and a radius R=0.625 m. It turns on a frictionless axle. Its pulley has much smaller mass and a radius of r=0.230 m. The tension T u in the upper ( taut ) segment of the belt is 135 N, and the flywheel has a clockwise angular acceleration of 1.67 rad/s 2 . Find the tension in the lower (slack ) segment of the belt.
A way to test the tensile strength of a wire is to place a mass at the end of it and spin the mass with uniform circular motion. The speed at which the wire breaks is a measure of its strength. The maximum frequency of rotation before a certain wire breaks is 35.5 Hz. The wire is 50.5 cm long and has a mass of 0.656 kg. (a) Determine the speed with which the mass moves. (b) Calculate the centripetal force acting on the wire
In the figure, two 7.60 kg blocks are connected by a massless string over a pulley of radius 1.30 cm and rotational inertia 7.40 x 104 kg-m2. The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 1.20 rad in 154 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T, and (d) string tension T? Assume free-fall acceleration to be equal to 9.81 m/s?.
A block with mass m = 5.00 kg slides down a surface inclined 36.9° to the horizontal (Figure 1). The coefficient of kinetic friction is 0.27. A string attached to the block is wrapped around a flywheel on a fixed axis at O. The flywheel has mass 11.1 kg and moment of inertia 0.500 kg - m? with respect to the axis of rotation. The string pulls without slipping at a perpendicular distance of 0.300 m from that axis. Part A What is the acceleration of the block down the plane? Express your answer in meters per second squared. ? a = 1.45 m/s? Figure 1 of 1 Part B What is the tension in the string? Express your answer in newtons. 5.00 kg ? T = 11.6 N 36.9 國
A mass (M = 5.0 kg) is connected to a two pulley system. Pulley 1 has a moment of inertia, I = 0.5 kgm2, and a radius, R = 0.2 m. Pulley 2 has moment of inertia, I = 0.3 kgm2, and a radius, R = 0.15 m. The cord is spooled around pulley 2. The pulleys rotate about frictionless axles and the cord can be considered massless. (i) Determine the magnitude of the acceleration of m (ii) Determine the magnitude of the tension in the string attached to m (iii) Determine the magnitude of the tension between the pulleys.
A solid cylinder of mass M = 1.06 kg and radius R = 13.0 cm pivots on a thin, fixed, frictionless bearing (see Figure). A string wrapped around the cylinder pulls downward with a force F = 3.139 N. Consider that instead of the force F, a block with mass m = 0.32 kg (with force F = 3.139 N) is attached to the cylinder with a massless string: The cylinder is changed to one with the same mass and radius, but a different moment of inertia. Starting from rest, the mass now moves a distance 0.5647 m in a time interval of 0.57 s. Find Icm of the new cylinder.
A spool of thread consists of a cylinder of radius R₁ = 4.5 cm with end caps of radius R₂ = 9.0 cm as depicted in the end view shown in the figure below. The mass of the spool, including the thread, is m = 280 g. The spool is placed on a rough, horizontal surface so that it rolls without slipping when a force T= 0.620 N acting to the right is applied to the free end of the thread. For the moment of inertia treat the spool as being a solid cylinder of radius R₁, as the extended edges are thin and therefore light. (a) What is the acceleration of the spool? Take positive to be to the right. .739 m/s² (b) Determine the direction of the force of friction. to the left to the right straight up straight down