- Write the Gilven and what is being asked..Write your complete solution.-Round off your answers into TWO decimal places-BOX your final answer and don't forget the units. 4. A thin hollow sphere of radius 300mm and thickness 2.5m is subjected to an internal pressure.Determine the internal pressure if the tensile stress of an element in the sphere is 630kPa.

Answered: Image /qna-images/answer/f523c9d0-75ce-4945-9385-a8de0b495ec6.jpg

Answered: A thin hollow sphere of radius 300mm…

A thin hollow sphere of radius 300mm and thickness 2.5m is subjected to an internal pressure. Determine the internal pressure if the tensile stress of an element in the sphere is 630kPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The same circular plate, as in the previous questions, is considered. Assume a plate radius of Ro=490mm and a plate thickness of h=9.64mm, respectively. Also, assume that the plate is subjected to a uniform pressure of P=1,440 KPa, and that the plate is made of a material of Poisson's ratio V=0.34. Find the absolute value of the radial stress at the centre of the plate in KPa. NOTES: type in your answer without considering any negative sign; round-off your answer to 4 decimal places. ↓ r> P Ro VIT
A basketball has a 300-mm outer diameter and a 3-mm wall thickness. Determine the normal stress in the wall when the basketball is inflated to a 120-kPa gage pressure.
A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which has an outside diameter of 40mm and an inside diameter of 30mm. The length of the brass tube exceeds that of the round steel bar by 0.12mm. Rigid plates are placed on the ends of the tube through which an axial compressive force is applied to the compound bar. Determine the compressive stresses in the bar and tube due to force of 60 kN. Use 200 GPa for modulus of elasticity of steel and 90 GPa for modulus of elasticity of brass.
04 It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm (find the thickness and external diameter). External pressure is zero. Knowing that the ratio between the internal pressure to maximum hoop stress is 0.4. Also find the change in thickness of the metal when the internal „pressure is 500 bar. Take E=210 MN/m2 and v-0.3 SN= 32
Applied mechanics: An undersea research vehicle has a spherical hull of 1m radius and a 40mm thickness. The hull is constructed of high strength alloy steel having a yield point of 700 MPa. Neglecting the adverse effect of entrance ports cut into the hull determine the depth the vessel may be submerged to set up a stress equal to that of the yield point. Relative density of sea water = 1.023
A rubber bolt is inflated to apressure of 65kPa. At that pressure, tediameter of the ball is 240mm and the wall thickness is 1.25mm. The rubber has a modulus of Elasticity = 3.7 MPa and Poisson’s ratio v=0.48. Determine the maximum stress in the ball if its stress is half that of the cylinder
A steel wire 5-m long hanging vertically supports a weight of 1200 N. Determine the required wire diameter if the stress is limited to 140 MPa and the total elongation must not exceed 4 mm. Neglect the weight of the wire and assume E = 200 GPa.
The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. If the tank wall has a thickness of 50 mm for cylindrical and hemispherical shells, The bolts were installed as 40 bolts/meter. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. What is the maximum pressure that tank can contain.
A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The 0.27] that has a yield strength vessel will be constructed from a special steel [E = 224 GPa; v = of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress in the vessel wall. Answer in MPa rounded-off to 1 decimal place.
A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of p = 420 kPa, determine its minimum required thickness if the maximum normal stress is not to exceed 12 MPa.
A hydraulic system is used to apply a force in an external fixation device to hold brokenends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure is 3 MN/?2 Determine The stress in the piston rod which has dimeter of 4 cm
A thick cylinder of 0.5 m external diameter and 0.4 m internal diameter is subjected simultaneously to internal and external pressures. If the internal pressure is 25 MN/m2 and the hoop stress at the inside of the cylinder is 45 MN/m2 (tensile), determine the intensity of the external pressure,