A thin 5-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless hinge at point O, as shown in the figure below. The horizontal portion of the gate covers a 2-ft diameter drain pipe, which contains air at atmospheric pressure. Determine the minimum water depth, h, at which the gate will pivot to allow water to flow into the pipe. Assume w-5 ft. D=2 ft. L=2 ft. 7= Width W Right-angle gate. Hinge. Water D

Q: ]means the repair work done to keep the system in good working condition.

A: It is required to fill the blank

Q: A drive system consists of single strand chain running on a 22 tooth drive sprocket at 1600 rpm. The…

A: Solution: Given Data: Ts=22Ns=1600 rpmP=0.5"NL=280 rpmC=D+0.5d

Q: In a manufacturing company, the routing of part A is started from machine X, and continued by…

A: Given:To find:Available processing time for machine X.

Q: v) w) What is the distance, dsy, of shape 5's centroid from axis Yo? What is the distance, dzy, of…

A: (v) Consider the shape 5 and calculate the distance, d5y, of shape 5's  centroid from axis y0.

Q: In the photos it show the steps to solve for t(time), I don't know how they got .3924 towards the…

A: The formula used for calculation of time is known as Fick’s second law formula Erf stands for error…

Q: S) t) What is the distance, d3x, of shape 3's centroid from axis Xo? What is the distance, d6x, of…

A:

Q: 180 200 30 Find F and Lacation 令 ocation 200

A:

Q: Given data: Applied force=3N Distance covered%3D5 m Determine work done

A: Given data : Distance covered=d Applied force=F   To find : Work done

Q: (3) In Sample Problem 15.04, the constant"kappa" is *

A:

Q: In a manufacturing company, the routing of part A is started from machine X, and continued by…

A: Given:Machine XMachine YMachine ZPart AStandard timeScrap EstimatePart BStandard timeScrap…

Q: 22. A man borrowed P300,000 from a bank and agreed to pay the loan at the end of the months. The…

A:

Q: A diesel engine in a power plant has an output of 150 KW at 260 rpm. It uses fuel oil having a…

A: Given data: Diesel engine power output = 150 kW @ 260 rpm Calorific Value of Fuel oil = 43912 kJ/kg…

Q: Find the work W done by a force of 3 pounds acting in the direction 45° to the horizontal in moving…

A:

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: can make it in Solidwork

A: Given Structure To find 3D model

Q: Question 2: The cost of a machine is 6200 S and scrape value is 130 S. The maintenance costs found…

A: Given data Cost of machine (C) = 6200 Scrap value (S) = 130

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

A:

Q: The other part of the question is not solved please look at it

A: Normal stress in the x direction, Normal stress in the z-direction, Shear stress in the x-z plane,…

Q: I needed it to be solved using differential equation

A:

Q: A screwdriver is a kind of wheel and axel machine where the radius of the handle is the input…

A: Given data: The diameter of handle, d1 = 1 in. The diameter of the shaft, d2 = 1/4 in. Write the…

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: to the ght rigid bar are identical except for ength. Before the load W = 6500 lb. ras attached, the…

A:

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: • Use hexagonal head screw/bolt with jam locking nut through clearance holes to fix the two parts…

A:

Q: Q.1: Select the correct answer: (1) (A) Graphical method is used when most of the problems of linear…

A: 1. Graphical method is used when most problems of "linear programming" includes two decision…

Q: oy. Suppose the vessel is subjected to uniform intemal pressure p, determine the minimum thickness…

A:

Q: What is the difference between corrective maintenance and preventive maintenance ?

A: After equipment fails, corrective maintenance (CM) entails its replacement or repair. When…

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: Hello, sorry for not clarifying which parts to solve, could you please do part D?

A: Given data:- The speed of the impact is doubled To find:-the maximum compression of the spring

Q: General Directions: Solve what are asked for in the following problems. Show complete solutions by…

A:

Q: Give a steps by steps answer of the solution

A:

Q: A centroid is an object's geometric center. For an object of uniform composition, its centroid is…

A: Hi, As per the guideline, we can not provide you with a handwritten solution.

Q: Findss 30 kN-m

A:

Q: Which of the following statements is FALSE regarding materials experiencing stress within the…

A: Given Stress vs strain plot To write:  WHich statement is false

Q: Two models of controlling boards. The 1* type has high specification for work from the 2nd type. The…

A: Let us consider that the quantity for the first type is x1 and quantity for the second type is x2.…

Q: can u solve the question using newton or lanrnage method in detail with hand written notes

A: Free body diagram mx¨1+cx˙1+kx1-x2=0 Rearranging mx¨1+cx˙1+kx1=kX2sinωt