(a)The homogeneous, 250 kg mass triangular plate shown in Fig. Q1(a) issupported by pin A and a roller at C. Angle B is 90°.0.6m30Fig.Q1(a): Triangular Plate(1)Draw the Free Body Diagram (FBD) for the plate.(ii)Determine the magnitudes of the reaction forces atNote: The centre of mass of a triangle is at 1/3 of its height asand C.measured from the base.

Answered: Image /qna-images/answer/0138ea87-569b-41da-b729-cf2e64822717.jpg

(a) The homogeneous, 250 kg mass triangular plate shown in Fig. Q1(a) is supported by pin A and a roller at C. Angle B is 90°. 0.6m 30 Fig.Q1(a): Triangular Plate (i) Draw the Free Body Diagram (FBD) for the plate. (ii) Determine the magnitudes of the reaction forces at A and C. Note: The centre of mass of a triangle is at 1/3 of its height as measured from the base.

(a) The homogeneous, 250 kg mass triangular plate shown in Fig. Q1(a) is supported by pin A and a roller at C. Angle B is 90°. 0.6m 30 Fig.Q1(a): Triangular Plate (i) Draw the Free Body Diagram (FBD) for the plate. (ii) Determine the magnitudes of the reaction forces at A and C. Note: The centre of mass of a triangle is at 1/3 of its height as measured from the base.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following figure shows a hollow piston of weight W=50 N and diameter D=3d occupies the position initial displayed. The lateral tube has a diameter d₁=d/2. Find the descent of the piston for the equilibrium position. (b=12 cm, d=8 cm, y=104 N/m³). TBL Agua D d₁
I need the answer as soon as possible
The traffic light shown in (Figure 1) has a mass of21 kg . Take h= 3.5 mm.
(b) A structure in Figure Q2(b) is supported by a pin at A and a roller at C. Forces were applied to the structure as shown. The weight of the structure is negligible. 2 kN 5 kN E 2 kN 2 m A В C D 2 m 1 m 1 m Figure Q2(b): Multi-force structure. (i) Draw the free body diagram for the structure. (ii) Determine the reaction force at A and C.
The lid shown has a mass, m = 60 kg, and is held in position by rod AB. The rod is held in place by rounded surfaces at A and B, where B is right at the edge of the lid. The hinges at C and D rotate smoothly and only the hinge at C provides a reaction force along its axis (the x-direction). a = 950 mm, b = 300 mm, c = 55 degrees Determine A) Reactions at hinge C and D B) Reaction force in rod AB C) The minimum coefficient of friction that is needed between the rod and the lid to maintain this position
Fig. 1 shows a simple six bar linkage held in static equilibrium while a torque Tin = 250 N mm is applied. Determine the reaction forces at each joint and the holding force P by considering the free-body diagrams of each member. Each small square on the grid is 50 mm by 50 mm. H E Figure 1 Simple Six Bar Linkage B Tin
I need the answer as soon as possible
a garage door 15 ft long and 8 ft high weighs 80 lbs. the hinges are 1.5 ft from the upper and lower sides respectively and the upper hinge carries the entire weighs of the door. find the reaction of the upper hinge.
a garage door 20 ft long and 10 ft high weighs 90 lbs. the hinges are 2 ft from the upper and lower sides respectively and the upper hinge carries the entire weighs of the door. find the reaction of the upper hinge.
A semicircular floodgate is 4.0 m long and 3.0 m radius. It is articulated at its lower point and has a latch at its top point. disregarding the weight of the gate, what will be the reaction forces on the latch and joint? NA