(a) The Fe-C phase diagram is show in Figure Q5(a). Answer the following questions based on the phase diagram. (i) The microstructure of an iron-carbon alloy consists of proeutectoid ferrite and pearlite; the mass fraction of these two phases are 0.28 and 0.72, respectively. Determine the concentration of carbon in this alloy. (ii) What is the carbon concentration in the eutectoid and proeutectoid ferrite of a Fe-0.2 wt%C alloy? (iii) Schematically sketch the microstructures of hypocutectoid and hypereutectoid steels at room temperature. T(°C) 1600 1400 y+L A I+Fe.C 1200 (austenite) 100아 1148°C y+Fe,C 800 727°C 60아 a+Fe,C 4004 0.022 0.75 6.7 C, wt% C Figure Q5(a) Fe-C phase diagram *4.30 6 Fe,C (cementite)

(a) The Fe-C phase diagram is show in Figure Q5(a). Answer the following questions based on the phase diagram. (i) The microstructure of an iron-carbon alloy consists of proeutectoid ferrite and pearlite; the mass fraction of these two phases are 0.28 and 0.72, respectively. Determine the concentration of carbon in this alloy. (ii) What is the carbon concentration in the eutectoid and proeutectoid ferrite of a Fe-0.2 wt%C alloy? (iii) Schematically sketch the microstructures of hypocutectoid and hypereutectoid steels at room temperature. T(°C) 1600 1400 y+L A I+Fe.C 1200 (austenite) 100아 1148°C y+Fe,C 800 727°C 60아 a+Fe,C 4004 0.022 0.75 6.7 C, wt% C Figure Q5(a) Fe-C phase diagram *4.30 6 Fe,C (cementite)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

During a quenching process on a TTT diagram, we can transform pearlite into bainite. True or false?
Answer ASAP
In Figure 1 (phase diagram), an alloy composition of 95 wt% Mg and 5 wt% Al is cooled from 700 C to 475 C. An analysis of the resulting ε solid-phase composition reveals that it has a higher Mg content than is anticipated by the phase diagram.a) Explain why this might be the case and how your reasoning results in the higher-than-expected Mg content.b) Provide a sketch showing the likely distribution of Mg content within the volume of ε solid-phase.
Can you draw on the sketch and show all steps
Figure 2 refers to the phase diagram for silver and tin. Label the regions (1) to (5) Temperature, 0/°C 1000 800 600 400 200 0 Liquid 2 Ag,Sn 60 a 20 40 80 Mass percentage Ag/% 100 Question 6: What will be observed when liquids of composition of 40% Ag are cooled to 200 K? When will it begin to precipitate? When will it become solid?
1. Figure 1 shows copper-nickel piping on a marine chemical tanker. As an inspection engineer, one day you were called to inspect a corrosion problem that occur on surface of the pipe. From microstructural investigation, you find out that the corrosion problem is caused by composition variation across the grain as shown in 2. Using phase diagram given, rationalise this microstructure. Your explanation should include why there are two shades of grey colour in the microstructure and what are their compositions? You are free to choose which ever copper-nickel system (example 80% Cu – 20% Ni) you like from the phase diagram. Figure 1 0% Ni 25% Ni 50% NI 75% Ni 100% N 1500 Liquid °C 1400 1330°C 1300 Liquidus jihe 1290°C 1200 LAS Soligus line 1100 400um Solid 1000L 100% Cu 75% Cu 25% Cu 50% Cu 0% Cu Figure 2 2. you have been introduced to one type of annealing heat-treatment, which is process-annealing also known as subcritical annealing. But there are a lot of other type annealing process…
Consider a Fe-0.5% C alloy. What is the amount of pro eutectoid phase (in percentage ) just above the eutectoid temperature
I need neat and clean handwritten solution. Don't give typed solution. Correct answer will be upvoted only.do remember
Correct and complete solution please
Material science Assuming this system forms a laminar type eutectic, determine the volume proportion of phases for an equilibrium solidified 50% Pb alloy. Sketch the expected microstructure.
A hypothetical eutectic phase diagram for metals A and B shows that cooling a liquid melt with a concentration of 50 wt% A-50 wt% B to just below 625 °C (eutectic isotherm temperature) results in simultaneous formation of alpha and beta phases. The phase diagram also shows that alpha (A rich) and beta (B rich) phases exist at left and right extremes of the phase diagram, respectively. At the eutectic isotherm temperature, the maximum solubility of B in A and A in B is 10 wt% and 5 wt%, respectively. The phase diagram does not have any intermetallic compounds. A new solid alloy is made by melting together 86 gr of a 40 wt% A-60 wt% B alloy with 136 gr of 65 wt% A-35 wt% B alloy followed by cooling the melt to 400 °C. If the new alloy is heated up from 400 °C to just below 625 °C, answer the following questions: a. Calculate the overall alloy composition. b. Determine phases present and calculate their respective masses. Calculate the masses of the primary phase, eutectic phase, and…
please answer correctly and completly