A T-shaped built up steel beam is composed of 150 mm x 10 mm flange plate at top and a vertical web plate 250 mm x 19 mm. All plates used are A36 steel. Calculate the location of the horizontal plastic neutral axis measured from the top edge of the flange.

Q: 2. Please average the following two angles, a = 73° 25' 12" and xß = 73° 54' 00", and present the…

A:

Q: Q1: For the shaded area shown in the figure below, determine the centroidal coordinates (xo,yo).…

A:

Q: Calculate the Ix and ly of the given figure if location of x-axis is as shown and y-axis is at the…

A:

Q: Question #1: Find the (x,y) coordinates of the centroid for the shaded area shown in the figure…

A: Equation of parabolic triangle, Equation of triangle, To find: The centroid of the shaded portion…

Q: Subject: Fluid Mecha

A: Step : 1 Surface tension :-It is defined as the tensile force acting between two immisible fluid…

Q: Find the area of a rectangle with a length of 6 inches (in) and a width of 2 inches.

A: Solution:- A rectangle is a two dimensional shape or polygon with four sides, four vertices, and…

Q: Problem 19-24: A B 30⁰ Determine the maximum force P that can be applied without moving the two Y-kg…

A: only Y = 37 kg is used  and acceleration due to gravity g = 9.81 m/s2 is used

Q: Consider the "H" section shown in the figure below. 1) What is the distance to centroid (x¯)?…

A: To find location of centroid

Q: Problem 9-12: y-axis 90 mm 100+ V (mm) 60 mm x-axis

A: Given Data:X=137, Y=37, A=6, B=8, C=1 The solution to the above given questions are as under-

Q: Problem #8 A (m) E D Y (N) 2 m F X (N) |C 2 m A В

A: Determine force in all members of truss?

Q: what about K ? how did you calculate 39 ? when I do my calculations I find 35

A: K - Rate of vertical curvature. The value of K is not a calculated one which varies depending on the…

Q: 30 „5 in. 18 in. B

A: to find - moment about A in given illustration

Q: Q5. What is the minimum clearance required by OSHA regulations between a crane and a 150-kV power…

A: The Occupational Safety and Health Administration(OSHA)-The Occupational Safety and Health…

Q: For the illustrated section: (7 inch, 5 inch, 2 inch) Determine: (a) the moment of inertia with…

A:

Q: W = X N 1m 1ms=0.4 Determine the normal force between the crate and the surface Determine the force…

A:

Q: 6" 2" 3" 4" 4"- 6" Using the figure above, calculate the following 1. Total area of the figure, in2…

A:

Q: The figure is made of a 4"radius half-circle inscribed in a 4" x 8"rectangle beside a 4"x 6"…

A:

Q: Problem 13-14: XN H4,-0.3 Determine the normal force between the crate and the surface Determine the…

A:

Q: Problem 3.10 12 in. 15 in. 4 #10 bars $3 in. f, = 60,000 psi f = 4,000 psi 18 in.-

A:

Q: Find the area of the object below. Round to the nearest unit. SHOW YOUR WORK IN THE ANSWER BOX BELOW…

A: We will divide the whole area into 4 different parts.

Q: Determine the maximum safe capacity of an axially loaded hinged ends column having an unsupported…

A: This is already answered question.In this question ask about that how we get the Circle value.(ie…

Q: Given the following cross section , find the area of the cross section

A: Given Details of a cross section  Required  Area of cross section

Q: With respect to the given X & Y axis of the shaded section.

A:

Q: Y 400 mm 300 mm r= 200mm 75 mm **Units in mm 300 mm 150mm 75 mm 50 150 50

A:

Q: Determine the force (P) required to cause impending motion, given that us = 0.43 and µk = 0.25. F1 =…

A: solution - Given Data:-  F1 = 506  Coefficient of static Friction = 0.43 Find, the value of P

Q: Draw the following figure on an outer piece of paper and measure with a ruler approximately the…

A:

Q: What is the reading from the following dial caliper? 90 80 20 70 001 30 60 40 50

A: Reading from main scale = 2.3. Reading in dial caliper = 65 Least count of dial  = .001 Dial reading…

Q: Find the moment of inertia (Ix, mm") of the composite shape from the bottom pase. Type answer in two…

A:

Q: Compute the moment about point A. Use F-1400 pounds and theta - 25 degrees. Show all work on your…

A: Answer Resolve the Force F into its horizontal and vertical component and show it on given frame as…

Q: The interior angles of a spherical triangle LUV and side LU were measured as follows: L= 61°45'30" U…

A:

Q: Problem 15-16: 2 m W = XN |--1m-| H₂=0.3 Determine the normal force between the crate and the…

A:

Q: What is the total area of the two triangle shapes (a) and (b) (in square inches)? 182.25 X Your…

A: Given, To find side 1, 2 ,3 and 4 Total area of two triangle shape (a) and (b) Area of rectangle…

Q: How much does the bar, shown in the following figure, elongate? All bars have the circular ca…

A: Given -

Q: Using the Z section below as a reference, determine the following: Yo 1.5 1.5 Хо 8.0 t.5 Compute the…

A: The given section is a composite section. Divide the section into set of rectangles to use the…

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.