Draw the following figure on an outer piece of paper and measure with a ruler approximately the length of the dimension Y Index (dimensions in millimeters) 38 30 36 34 120 120

Q: Given the following, determine the centroid about the x-axis for the following problem. Please show…

A: Give the information:Required:Centroid about the x-axisSolution:To determine the centroid about the…

Q: d = 4" %3D x' b = 4" %3D B = 8" %3D H = 8" h = 4" d = 4"

A:

Q: . . .

A: The volume of given figure with regular polygon at top and base is as under

Q: (a)   Determine the coordinates of the centroid with respect to point “O”.  (b)   Find the second…

A: To find centroid and moment of inertia about x axis

Q: Locate the centroid of the plate area shown below: (All units are in mm). Ø200- Ø150 300 300 Ø50 50…

A:

Q: y 74 mm 36 mm - 36 -+ 36 mm mm Answer: y = i mm

A:

Q: Find the centroid of the profile in the figure shown with respect to the origin of coordinates…

A: Given:Required:Location of centroid

Q: Consider the "H" section shown in the figure below. 1) What is the distance to centroid (x¯)?…

A: To find location of centroid

Q: what about K ? how did you calculate 39 ? when I do my calculations I find 35

A: K - Rate of vertical curvature. The value of K is not a calculated one which varies depending on the…

Q: but I nee

A: Draw the figure Consider a differential element of size dy

Q: R10 30 50 O. 15 R30

A:

Q: Determine the Radius of Gyration about the X axis

A: Consider the free body diagram;

Q: k-d a b-

A: Consider the following diagram

Q: 23mm R2 166.5mm 28° 34° 235mm 175mm 250mm R1 R3 125mm

A:

Q: 4. Find the location (x, ỹ) of the centroid of the following shape using the origin given. 55 mm 45…

A:

Q: Q1: - Determine the centroidal coordinate of the shaded area shown in the figure below. Assume all…

A: ##CENTROIDAL Coordinates of Shaded Area ####

Q: Determine the coordinates of the centroid of the lines shown with respect to the indicated X and Y…

A:

Q: v2 y1 x2

A:

Q: Whered you get "K"? I use this formula but it does not match

A: Solution: Hazen William formula: V=kCR0.63S0.54 Where, V = fluid velocity, m/s, ft/s C = factor for…

Q: 14. For the given figure below, determine the coordinates of the centroid of the plane region with…

A:

Q: The I-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

A: Given:-   D = 248 mm W =136 mm To find:- Second moment of inertia about x-axis

Q: Calculate the magnitude of TXZ at point A for the beam of cross section T. Consider the forces,…

A:

Q: a = 20 mm b = 100 mm c = 200 mm d = 70 mm e = 60 mm f= 70 mm g= 50 mm h = 20 mm

A: Given  a= 20mm b= 100mm c= 200mm d= 70mm e= 60mm f= 70mm g= 50mm h= 20mm second moment of area about…

Q: Compute the coordinates of the centroid (, ) of the area shown. лу ка a- | a b 2013 Michael Swanbom…

A: Answer  The x coordinate of the centroid is  x = -4.52 mm    The y coordinate of the centroid is  y…

Q: A rectangular block of metal has a dimension of 21 cm, 77cm and 24 cm. The block has been melted…

A:

Q: roid (7, g) of the area showr

A: Note : we can solve first three part for you according to bartleby guidelines  Given:- a = 27 cm b…

Q: What is the area of the below figure if you know x=24.4? (use trapezoidal rule) Ar 29 27 25 27 25 22…

A:

Q: What is the reading from the following dial caliper? 90 80 20 70 001 30 60 40 50

A: Reading from main scale = 2.3. Reading in dial caliper = 65 Least count of dial  = .001 Dial reading…

Q: What is the moment of inertia of the section about the z-axis? in mm) R Radius of hole = 3. Radius -…

A:

Q: Determine the shape factor of the cross section.

A:

Q: Rotate the objects shown below by the indicated amount and sketch the result in the space provided.…

A:

Q: Amperes is measurement unit for pressure while Pascal is a measurement unit for current. Select…

A:

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.