A system of costumers X, Y, and Z are supplied by a common distribution transformer. Estimate the peak load on the transformer in kW. Refer to the tables of typical values of demand factors and diversity factors. ▪ Customer X: store building with 5-kW lighting and 25-kW small motor power I Customer Y: store building with 18-kW lighting and 35-kW small motor power Customer Z: office building with 55-kW lighting and 80-kW large motor power I

A system of costumers X, Y, and Z are supplied by a common distribution transformer. Estimate the peak load on the transformer in kW. Refer to the tables of typical values of demand factors and diversity factors. ▪ Customer X: store building with 5-kW lighting and 25-kW small motor power I Customer Y: store building with 18-kW lighting and 35-kW small motor power Customer Z: office building with 55-kW lighting and 80-kW large motor power I

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 200 – kVA transformer with impedance of 5 percent and the power factor of the load is 85percent. The primary voltage is 6,000 volts while the copper loss is 5 kW. Find the percentageregulation.
Please answer all subparts than i will like a. A current transformer (CT) is rated 200/5 and has a secondary current of 4.0 A. Determine the primary current. b. A 150/5 CT has the primary conductor looped to pass through the donut three times. If the secondary current is 3.0 A, determine the primary current. c. A 60/5 CT has the primary looped to pass through the donut two times. With 25 A in the primary, determine the secondary current. d. A voltage (potential) transformer is rated for 14.4 kV / 115 V and is used to measure the voltage on an industrial power line. If the voltmeter indicates 111 V, calculate the voltage in the power line.
Nominal tests 50 kVA, 20,000 / 480 V, 60 Equivalent of single phase transformer in Hz to determine circuit parameters Table of data for experiments presented. a. Obtain the T-equivalent circuit of the transformer reduced to secondary. b. Calculate the efficiency of the loaded transformer with 0.7-inductive power factor at the label current. c. The transformer is connected to the 50 Hz network and 0.7-inductive power factor at the tag current loaded with. Calculate the efficiency of the transformer.
3) A three-phase transformer of 60 kVA (three-phase power), 13200/480 V (line A line) in delta-strella connection has a resistance of 0.02 PU and a reactance of 0.08 PU. For this transformer, calculate: a) The voltage regulation at full load and F.P. 0.85 in delay. (b) The regulation of voltage voltage to full cargo and F.P. Unitarian. c) The voltage regulation at full load and F.P. 0.85 in advance.
4) A 2300/230V , 60Hz transformer takes 0.5A at a power factor of 0.25 on open circuit when supplied at 230V. (A) find the resistance representing the core loss in ohms, (B) find the magnetizing reactance of the core in ohms, (C) find the magnetizing current in amperes,(D) fine the core loss components of current in amperes Subject Electrical Apparatus and Devices
Do the following: Solve for the voltage across the appliance and the current through it by referring the appliance to the transformer primary. (Assign the convenience outlet voltage as the reference phasor i.e. at 0o) Draw the circuit that would solve for VL and IL. Compute all referred values and label all components. Solve for VL and IL
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 13.2 (line-to-line) kV. The step-down transformer has a turn ratio of 15:1 and it has a Y-connected, balanced load of 0.667 +j 0.111 ohms connected to its secondary side. A capacitor bank of -j0.239 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: A. 5118 V B. 6.2 kV C. 8865 V D. None of the other choices are correct E. 4225 V
a single-phase transformer serves a 7.2kw resistive loadlocated 200 ft from the transformer. each conductor from the transformer to load has an impedence of (0.78+j0.052) ohms per 1000ft. if the voltage at the load terminal is 240v, the magnitude of the voltage (v) at the transformer secondary is most nearly:
Q1 The oil test condition analysis is the ultimate starting point for any HV transformer assessment. Like blood testing in human beings, it's an essential indicator of good health. i) Sketch HV Oil test condition setup to test the condition of HV power transformer with detailed labeling. ii) As a testing engineer, how do you check the condition of transformer? iii) How often should transformer oil be tested as per industrial practice? iiii) How to improve the life of the transformer oil?
Solve the following problems with complete solutions and units usingtwo(2) decimal digits.2. A 5-kVA transformer has 35 W. core loss and 40 W. copper loss atfull-load. It operates at rated kVA and 0.8 power factor lagging for 6hours, one-half rated kVA and 0.5 power factor lagging for 12 hoursand no-load for 6 hours. What is the all-day efficiency?
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
8. A 10 power transformer supplies a load 8 kW of power at a power factor of 0.77 lagging at full load. The voltage at the load is 115V. The transformer has 1200 turns on its primary and 450 windings on its secondary. The iron loss is 325 Watts and the primary copper loss is 150 Watts and the secondary copper loss is 260 Watts. Find a) The full load apparent power and the secondary and primary currents at full load. b) The resistance of the primary and secondary windings. c) The transformer's full load operating efficiency as a percent.