A surveyor measured the distance between two points marked on the plan drawn to a scale of 1 cm = 1m (R.F. = 1:100) and found it to be 40m. Later he detected that he used a wrong scale of 1cm = 50cm (R.F. = 1:50) for the measurement. Determine the correct length

A surveyor measured the distance between two points marked on the plan drawn to a scale of 1 cm = 1m (R.F. = 1:100) and found it to be 40m. Later he detected that he used a wrong scale of 1cm = 50cm (R.F. = 1:50) for the measurement. Determine the correct length

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The table below gives area information on earthwork of road cross sections at three different…

Q: Explain how you will set-out a point that perpendicular to a straight line using two tapes.

A: Setting out: This method is used to establish the position of the trench and wall of the house as…

Q: - () 4 B+tan R 2- B = and H = for triangular spoil bank \L+tan R, 2 HIN

Q: An Engineer measured the distance between two locations on a plan having a scale of 1 cm = 50 m as…

Q: Calculate the volume of the earthwork using the End Areas and Prismoidal methods.

Q: Q3)The figure below represents a grid for a parcel with (25 mx 25 m) sub-grid dimensions Draw the…

A: Solution:

Q: Intersection return at First Street,

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: The areas in cut of two irregular sections 45 m apart are 44 m^2 and 66 m^2 respectively. The base…

A: Given values: Area of 1st cut, A1 = 44 m2 Area of 2nd cut, A2 = 66 m2 Distance between the cuts, L =…

Q: What is Shape Correction Factors For Alpan (1964) Method ?

A: Alpan method (1964) It is based primarily on peck and Terzaghi method (1948). It evaluates the…

Q: A surveyor measured the distance between two points on the plan drawn to a scale 1 cm = 40 m and the…

A: Original scale- 1 cm = 40 m, Wrong scale- 1 cm = 20 m, Measured length L=468 m, To Find- The value…

Q: Simpson's 1/3 Rule can only be applied when the number of segments or strips used to approximate the…

A: Answer:- False Explanation:-In order to apply Simpson's 1/3 rule the number of segments must be odd.

Q: The cross-section notes shown below are for a ground excavation for a 12m wide roadway. STA 12+2800…

Q: 5. ( After surveying a construction site, the surveyor produced the following grid below. If you…

A: Given data - Existing elevation = 1 ftFind out - Calculate the total cut volume?

Q: final bearings must be written along the appropriate lines be

Q: Q2/ For the land shown below, if the length of squares is (30m) and the scale is (1:1000). Find: 1-…

A: Given: Square Length L=30m scale 1:1000 contour interval=1m find the followings 1 no. of contours…

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 16+4400…

Q: Q13. If the known benchmark elevation is 272.5 ft. When surveying you find the rod reading at PT. A…

Q: 4. For this oblique triangle, what is the length of side b given the following data: Angle B =…

A: Given: a = 125 ft c = 200 ft Angle B = 38o 15'

Q: Briefly explain why should blank determination be performed.

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 13+8300…

A: To Determine the cross sectional area at STA 13+8300.

Q: The table below gives area information on earthwork of road cross sections at three different…

Q: Sketch, at a scale of 1 inch = 10 feet, the general shape of contours crossing a 30 foot wide street…

A: Longitudinal gradeCross slopeWidth of each laneTo find: Distance between two contours and the sketch…

Q: 1. Using Simpson's one third rule, calculate the area of the plot shown in figure below. if the…

Q: 4] A foreman was asked to make a 550.45ft long line using a 50 m surveyor's tape that is 0.004m too…

A: Given data in question Distance 550.45 ft Tape 50 m 0.004 m long To find out Required distance

Q: Calculate the area A = ; x 1. 809 × 1.2| + [3.5 x 1. 2] %3D + (1.2 + 2. 8) (2. 8666) -(글 x 1.8666 x…

Q: The cross-section notes of an earthwork of a 10-m wide roadway having an area of 33.10 sq.m are…

A: Given data:- Width of roadway = 10 m Area of earthwork = 33.10 m2 Given equation,…

Q: = 3.086 GA Cm ,2.914 Cm 1,-1. Scm TOP most £ Lcft most Bottom most E Right mast Reference Reference…

Q: Complete the notes, find the elevation of point A and state the error in the network. Determine the…

A: HI= Elevation +BS Elevation= HI-FS

Q: Excavation for the borrow pits is shown in the figure, in which the numbers at the corners represent…

A: The diagram is shown below for the excavation borrow pits To determine the volume in cubic yards

Q: Show complete solution on Length for laying out, and Width for laying out.

Q: 1. Compute the area of sta 14 + 200 2. Compute the area of sta 14 + 300

Q: The following offsets are taken from a chain line to an irregular boundary towards right side of the…

Q: Given the description of the lot a. Make a sketch of the lot b. Compute the area of the lot c. A…

Q: 58. Given the data below determine the area of the cross section if the base is to be 10m wide. a.…

Q: What is similar flexure and contrary flexure and also draw a sketch what is the formula for…

A: Introduction- To assist in the transfer of railway and roadways vehicles from one track to another,…

Q: Please show detailed solution.

Q: Find the volume of the cut if the the area of a cross section of a profile 216 m from the initial…

Q: 6.9 5.75 2.1 2.5 1.5

Q: Find the area of each. Then put in square feet and square yards

A: 10)4' - 3 1/4" x 33' - 5" = (4 ft + 3.25 in) x (33 ft + 5 in) = (4 ft + (3.25 in * 1 ft/12 in)) x…

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 19+2600…

Q: Determine the interior angles of the parcel shown below. Provide a check. Show answers on the space…

Question

100%

A surveyor measured the distance between two points marked on the plan drawn to a scale of 1 cm = 1m (R.F. = 1:100) and found it to be 40m. Later he detected that he used a wrong scale of 1cm = 50cm (R.F. = 1:50) for the measurement. Determine the correct length.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A square prism of base edge 40 mm and height 50 mm is resting on its base. Develop its lateral surface on gridsheet.
In the figure below, determine the area included between the base line and the irregular boundary. 8.5 8.3 illing 4.5 2.5 3.0 6.0 2.0 3.9 4.2 2.2 6.0 5.9 9.0 11.6 Base Line ABC Note: All dimensions are in meters. Trace of the Irregular Boundary 8.3 5.1 4.6 11.2 4.8 5.5 X 10.2
Hello, can you please help me resolve this problem? My professor said that my computation of volume and fill is wrong. "Try drawing if you compute using the end area method, your area 1 for cut is correct but what is your area 2 for cut? The same is true with volume computation for fill. Please analyze the meaning of the cross-section for earth works is constant all throughout a 311.6 m length." Attached here are my computation and the problem given. If possible, please redo the computation. Thank you!
A surveyor starting from a point A moves N. 27° 40' E. a distance of 552' 7.25" to point B. Next, she moves N. 57°6' E. a distance of 409' 2.25" to point C. Next, she walks S. 6'5' Ww. a distance of 1692' 2.25" to point D. Finally, she returns to the starting point. What distance must she walk to return to the starting point? (Answer accurate to the nearest quarter inch.) feet & inches What heading does she walk from the fourth point to return to the starting point? (Answer accurate to the nearest minute.) N. W. What is the acreage of this plot of land? acre area = Your answer should be accurate to 3 decimal places. Notes: * the prime symbol in an angle represents minutes: 60' = 1° * the prime symbol in a length represents feet; double prime = inches; * 1 acre = 4840 yd? * 1 acre = 43,560 ft? an angle like N 20 E means 20 degrees east of north.
A Stream El = 3636.5-ft ✗ Land Surface = 3641.5-ft Stream 3638.5-ft = Scale: 1 inch = 5-ft Figure 1. Contour map of water around the brewery production well (2 ft intervals). A'
A line was divided into 4 segments and was measured through taping. The surveyors recorded the following data on their first trial: 20.3m, 12.1m, 15.8m, and 25.3m. On their second trial, the following data were gathered: 23m, 13m, 14.1m, and 23.1m. Determine the length (m) of the line.
Q2) Draw contours of 13m, 19m and 30m by interpolation method, with suitable scale. RLs at corners are shown on figure below. Recorded data are in meter. 22 13 7 25 19 14 31 28 23 5.00- 27 32 27 5.00
Help me slove in complete step by step and box the final answer. Write it on a clean bond paper
Determine: Use 3 decimals a) The width of the base b) The value of cut at station B if it has an area of 16.82 sq.m. b) The Volume of A and B with prismoidal correction (use end area method)
In Location surveys, this is where the surveyor sets stakes at important points along the centerline such as culvert locations, road intersections, beginnings and ends of curves, or breaks in the grade a. Important Stakes b. Centerline Stakes c. Grade Stakes d. Reference Stakes
Draw the figure to illustrate your understanding of all the problems.Show complete formulas and solutions.Round off to 3 decimal places. Enclose all finalanswers in a box.