A student performed a chromatography experiment to determine the Rf value of an unknown amino acid. The distances traveled by the amino acid and the solvent line were 3.0 cm and 8.5 cm, respectively. What is the R₁ value for this amino acid? 0.3 cm 0.35 1.8 O 5.5 0.85 cm 0.65 2.8

A student performed a chromatography experiment to determine the Rf value of an unknown amino acid. The distances traveled by the amino acid and the solvent line were 3.0 cm and 8.5 cm, respectively. What is the R₁ value for this amino acid? 0.3 cm 0.35 1.8 O 5.5 0.85 cm 0.65 2.8

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

You are creating a standard curve for a protein experiment. You have to stock solution of BS a and would like to obtain dilutions. Explain how you would create a 1:1000 dilution of your protein stock solution.
Three labs were contracted to measure the concentration of a 5.50 ppm Ca2* standard solution. They each measured the solution 3 times, and their results are as follows: Measurement 1 Measurement 2 Measurement 3 Laboratory 1 5.47 ppm 5.54 ppm 5.50 ppm Laboratory 2 5.32 ppm 5.44 ppm 5.56 ppm Laboratory 3 5.61 ppm 5.62 ppm 5.60 ppm Select ALL of the TRUE statements about the measurement capabilities of these labs. Lab #3 was the most precise. Lab #1 was the most precise. Lab #1 was the most accurate. Lab #2 was the most precise. O.Lab #2 was the most accurate. Lab #3 was the most accurate.
You use paper chromatography to separate the following two molecules. The stationary phase is coated with hexane C6H14 and the mobile phase is water. Which molecule will travel furthest up the paper? Explain using intermolecular forces between molecule and water. OH OH Phenol Napthol
Which is correct? Random errors affect accuracy and systematic errors affect precision. An accurate result shows agreement with the true or accepted value. Precise results can contain significant random error, but little systematic error. The standard deviation is a good measure of accuracy. Polydimethylsiloxane (PDMS) stationary phases have low polarities. Which of the following statements is TRUE about gas chromatography using PDMS stationary phases? The gas chromatography column is typically packed with silica microparticles. An oven is used to control the column temperature because a constant temperature is always needed in gas chromatography Octane (C8H18, boiling point: 126 ºC) is eluted later than dodecane (C12H26, boiling point: 216 ºC) 3-Pentanone ((C2H5)2CO, boiling point: 102 ºC) is eluted later than propanol (CH3CH2CH2OH, boiling point: 97 ºC)
3. A chemist used two different methods to measure the number of mg of Fe in five iron(II) sulfate supplement tablets. The results of each are shown below. 64.71mg Method 1: 65.03mg 61.55mg 64.9 mg 65.1 mg Method 2: 65.5 mg 66.1mg Calculate the average amount determined by each method as well as the standard deviation and RSD for each method. 63.07mg 65.4mg 67.15mg Which method gave more precise results? How do you know? Is it possible to know which method is more accurate? Why or why not?
Using figures 3 and 4 in the lab manual, rank each compound according to their polarity. For the least polar molecule, draw the structure and label any important functional groups on the molecule.
Standard deviation- 0.0371 mL, 0.0392 mL, 0.0392 mL, 0.03887 mL, 0.0398 mL Mean- 0.194 mL
1. As shown below, a student obtains two quality chromatograms for her distillate and pot samples, containing methanol and cyclohexanol. Match Chromatograms A and B with distillate or pot, and explain your conclusion. Circle your response: Chromatogram A A: Distillate or Pot Explain your answer: t=0 Chromatogram B B: Distillate or Pot
You have a 11.5 mg sample of blood that contains various proteins. Hemoglobin is the only protein in the sample containing Fe. Hemoglobin contains 3.83% by mass of a compound called heme (C₃₄H₃₂FeN₄O₄, MW = 616.49 g/mol). You find that your 11.5 mg blood sample contains 34.9 micrograms of Fe. What is the mass percent of hemoglobin in your protein sample? -don't prematureley round
Dr. Caras was characterizing a cytochrome (an iron containing protein) from a new strain of bacteria. He obtained eight measurements of the percent iron in the protein: 0.2409%, 0.2404%, 0.2394%, 0.2399%, 0.2515%, 0.2393%, 0.2409%, and 0.2392%. Calculate the mean (x) and standard deviation (s) for these results. % S = Use the Grubbs test to determine if one of these values is an outlier. What is the value of Galculated? Gcalculated = Should this potential outlier be rejected with 95% confidence? Critical values of G can be found in this table. The potential outlier should be rejected. The potential outlier should be kept.
Step by step full solution