A student attempts to determine the buffer capacity of a solution by titrating 40.0 mL of solution with 0.13 M NaOH. How many moles of base were added? Please report your answer to four decimal places. initial volume (mL) 2.26 final volume (mL) 20.63 initial pH 4.40 final pH 5.62 Your Answer:

A student attempts to determine the buffer capacity of a solution by titrating 40.0 mL of solution with 0.13 M NaOH. How many moles of base were added? Please report your answer to four decimal places. initial volume (mL) 2.26 final volume (mL) 20.63 initial pH 4.40 final pH 5.62 Your Answer:

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter15: Acid-base Equilibria

Section: Chapter Questions

Problem 107AE: A student intends to titrate a solution of a weak monoprotic acid with a sodium hydroxide solution...

See similar textbooks

Similar questions

Each symbol in the box below represents a mole of a component in one liter of a buffer solution; represents the anion (X-), = the weak acid (HX), = H+, and =OH. Water molecules and the few H+ and OH- ions from the dissociation of HX and X- are not shown. The box contains 10 mol of a weak acid, , in a liter of solution. Show what happens upon (a) the addition of 2 mol of OH- (2 ). (b) the addition of 5 mol of OH- (5 ). (c) the addition of 10 mol of OH- (10 ). (d) the addition of 12 mol of OH- (12 ). Which addition (a)-(d) represents neutralization halfway to the equivalence point?
What is meant by the capacity of a buffer? Describe a buffer with low capacity and the same buffer with greater capacity.
Two samples of 1.00 M HCl of equivalent volumes are prepared. One sample is titrated to the equivalence point with a 1.00 M solution of sodium hydroxide, while the other sample is titrated to the equivalence point with a 1.00 M solution of calcium hydroxide. a Compare the volumes of sodium hydroxide and calcium hydroxide required to reach the equivalence point for each titration. b Determine the pH of each solution halfway to the equivalence point. c Determine the pH of each solution at the equivalence point.
You are given the following acidbase titration data, where each point on the graph represents the pH after adding a given volume of titrant (the substance being added during the titration). a What substance is being titrated, a strong acid, strong base, weak acid, or weak base? b What is the pH at the equivalence point of the tiration? c What indicator might you use to perform this titration? Explain.
Another way to treat data from a pH titration is to graph the absolute value of the change in pH per change in milliliters added versus milliliters added (pH/mL versus mL added). Make this graph using your results from Exercise 61. What advantage might this method have over the traditional method for treating titration data?
Follow the directions of Question 64. Consider two beakers: Beaker A has a weak acid(K a=1105). Beaker B has HCI. The volume and molarity of each acid in the beakers are the same. Both acids are to be titrated with a 0.1 M solution of NaOH. (a) Before titration starts (at zero time), the pH of the solution in Beaker A is the pH of the solution in Beaker B. (b) At half-neutralization (halfway to the equivalence point), the pH of the solution in Beaker A the pH of the solution in Beaker B. (c) When each solution has reached its equivalence point, the pH of the solution in Beaker A the pH of the solution in Beaker B. (d) At the equivalence point, the volume of NaOH used to titrate HCI in Beaker B the volume of NaOH used to titrate the weak acid in Beaker A.
A solution of weak base is titrated to the equivalence point with a strong acid. Which one of the following statements is most likely to be correct? a The pH of the solution at the equivalence point is 7.0. b The pH of the solution is greater than 13.0. c The pH of the solution is less than 2.0. d The pH of the solution is between 2.0 and 7.0. e The pH of the solution is between 7.0 and 13.0. The reason that best supports my choosing the answer above is a Whenever a solution is titrated with a strong acid, the solution will be very acidic. b Because the solution contains a weak base and the acid (titrant) is used up at the equivalence point, the solution will be basic. c Because the solution contains the conjugate acid of the weak base at the equivalence point, the solution will be acidic.
Consider the weak acids in Table 13.2. Which acid-base pair would be best for a buffer at a pH of (a) 3.0(b) 6.5 (c) 12.0
Enough water is added to the buffer in Question 30 to make the total volume 5.00 L. (a) Calculate the pH of the buffer. (b) Calculate the pH of the buffer after adding 0.0250 mol of HCl to 0.376 L of the buffer. (c) Calculate the pH of the buffer after adding 0.0250 mol of KOH to 0.376 L of the buffer. (d) Compare your answers to Question 30 (a-c) with your answers to (a-c) of this problem. (e) Comment on the effect of dilution on the pH of a buffer and on its buffer capacity. Â
Sulfanilic acid (NH2C6H4SO3H) is used in manufacturing dyes. It ionizes in water according to the equilibrium equation NH2C6H4SO3H(aq)+H2O(l)NH2C6H4SO3(aq)+H3O+(aq)Ka=5.9104 A buffer is prepared by dissolving 0.20 mol of sulfanilicacid and 0.13 mol of sodium sulfanilate (NaNH2C6H4SO3) in water and diluting to 1.00 L. Compute the pH of the solution. Suppose 0.040 mol of HCl is added to the buffer.Calculate the pH of the solution that results.
Consider the titration of HF (K a=6.7104) with NaOH. What is the pH when a third of the acid has been neutralized?
A quantity of 0.15 M hydrochloric acid is added to a solution containing 0.10 mol of sodium acetate. Some of the sodium acetate is converted to acetic acid, resulting in a final volume of 650 mL of solution. The pH of the final solution is 4.56. a What is the molar concentration of the acetic acid? b How many milliliters of hydrochloric acid were added to the original solution? c What was the original concentration of the sodium acetate?