A stone (sg = 2.25) weighs 254 N in air. How much will it weigh in oil having sg = 0.80? A. 173.37 N C. 157.89 N D. 143.25 N B. 163.69 N What force (in Newtons) is required to completely submerge in water, a spherical ball having a diameter of 30 cm and weighing 5 kg? A. 89.65 C. 82.54 D. 104.78 B. 96.32 If 550 ml of a certain liquid weighs 6.8 Newtons, what is the density of the liquid in g/cm³? A. 1.32 C. 1.14 D. 1.48 B. 1.26

A stone (sg = 2.25) weighs 254 N in air. How much will it weigh in oil having sg = 0.80? A. 173.37 N C. 157.89 N D. 143.25 N B. 163.69 N What force (in Newtons) is required to completely submerge in water, a spherical ball having a diameter of 30 cm and weighing 5 kg? A. 89.65 C. 82.54 D. 104.78 B. 96.32 If 550 ml of a certain liquid weighs 6.8 Newtons, what is the density of the liquid in g/cm³? A. 1.32 C. 1.14 D. 1.48 B. 1.26

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

FORCES, RESULTANT & ΜΟΜΕNT B F1 76 DEG 2. The forces shown in the figure are directed at the midpoints of the sides of the triangular A 50 DEG F2 F1 = 40 KN F2 = 100 KN F3 = 80 KN 90° F3 rigid body. Compute the AB = 10.46 m BC = 11.20 m resultant of the forces. 90° 34° C HORIZONTAL
Answer with complete solution.
2. The block of weight W2 is being held in its position by two cylindrical rollers resting on inclined surfaces. All contact surfaces have a coefficient of static friction, us = 0.36. Wi is 380 KN. Ms Ms W, W, 1 60 W2 a. What maximum value of W2 it can be before slipping of the block happens? b. Determine the normal force reaction against the inclined surfaces.
5. A rigid bar AB, 9 m long is suspended by two vertical rods at its end A and B and hangs in a horizontal position by its own weight. The rod at A is brass, length 3m, cross-sectional area is 1000 mm? and E̟ =1×10°N/ mm? . The rod at B is steel, length 5 m , cross-sectional area is 445 mm?. At what distance 'd' from A may a vertical load P=300ON be applied if the bar is to remain horizontal even after the load is applied? ve stred Steel 5m Brass 3m P = 3000N B 9m
MECHANICS OF DEFORMABLE BODIES
5. A steel tape is 150 m. long at a standard pull of 65 N. Compute the pull correction in mm if during measurement the applied pull is 42 N. The tape has a cross sectional area of 3.18 mm² and a modulus of elasticity E = 200,000 MPa. A. -5.772 C. -4.321 B. -5.425 D. -5.936 6. The volume of a closed cylinder is numerically equal to its lateral area. The height is 18 m. Find the volume in m³. A. 198.7 C. 321.4 B. 257.8 D. 226.2 7. The offset distance from PC to PT of a simple curve is 24 m. The angle of intersection of the tangents is 19.5°. If the stationing of PT is 12 + 365.24, what is the stationing of PI? A. 12+295.47 SEC. 12 + 293.34 B. 12 + 296.32 D. 12 + 294.73 T
Knowing that P is 30 kN, applied to both sides of the bar at B and Q is 28 kN, applied to the bar at C as shown. What is the internal normal force acting on a vertical cross-section passing through the bar between points B and C? Express your answer in Newtons (not kN), to the nearest whole Newton, taking tension as positive and compression as negative.
Situation #2 El is Constant (Assume El = 1 kN-m²) B A kN/m A 7 m B= 8 A= 5 20. Determine the location of the maximum upward deflection from B. 21. Determine the maximum upward deflection. 22. Determine the maximum downward deflection All units must be in kN or m in the summary. Be consistent with your units.
The crate A weighs 780lb. Between all contacting surfaces, μs= 0.34 and μk= 0.29. Neglect the weights of the wedges. What force F is required to move A to the right at a constant rate?
111. two decimal places
Q2: 1.2 D.L x l.6 L.L Mu A: Find the maximum value of (p) that can be applied to the beam shown. Use f. =21.7 MPa and fy = 350 MPa (WD.L is included the self-weight of beam). %3D b hy P Wu =7 kN/m D.L 2028 A 500 mm 4028 250 mm -7.5 m-
Problem 01. (A-ODD) Given P1 = 40 Ibs and P2 = 100 lbs. (Use negative sign to indicate a direction of going down and going to the left.) 15 129 a. Determine the resultant of the two forces. b. Determine the components of the resultant along x axis. C. Determine the components of the resultant along y axis.