SITUATION: The tank shown in figure is accelerated to the right. Determine the total force acting on the bottom of the tank if the tank width is 1 m. Small air hole 0.2 m Air ax 1 m Water 2 m 40.657 38.158 35.316 31.025

Q: How many Type of Interior materils.

A: Interior materials : Interior materials are the materials which are used inside the house, like…

Q: Air duct straps are made from a 1-inch-wide strip of metal. The metal is 2463⁄4inches long. Each…

A: Calculate the numbers of straps of metal used for air duct. The length of metal is 24634inches.…

Q: Define Chemically Strenghfully Galss.

A: The type of glass which has increased strength by virtue of post-production chemical processes is…

Q: - consider the place acoustically ufficient, what kind of materials in hich shapes should be used,…

A: Instructions to Design A Conference Room For The Modern Office There's a ton to think about when…

Q: observe and describe the functionality and aesthetic aspects in their design.

A: By observing the picture it can be seen that the area is of restaurant or dinning area of a hotel.…

Q: Could you help with the reaction forces? Dy, Ay, Ax, Dx ? thanks

A:

Q: Pros and Cons of Dome Ten

A: PROS OF DOME TENT:- 1. It can be easily setup by only one person. 2. Can be easily stored and…

Q: What is the other name for air/cloth ratio?

A: The air to cloth ratio is defined as the total amount of air that is flowing through the filter of…

Q: Determine external and total indeterminacy

A: Given data : Number of external support reaction (R)=2+1=3Number of member (m)=3Number of joint…

Q: Explain Vibratory Hammers

A: The vibratory hammer: Vibratory Hammers is a device which is used ro drive the sheet piles into the…

Q: Discuss in detail Kennedy and Lacey Theory? Write down all the design steps.

A:

Q: What is LAP SPLICING? Illustrate a figure and explain it thoroughly

A: A lap is when two pieces of reinforcing bar (rebar) are overlapped to create a continuous line of…

Q: What are the responsibilities of the  mechanical, electrical, andstructural engineers

A: General responsibilities of mechanical engineer: Mechanical engineers seem to be accountable for…

Q: The elastic centroidal distance from the bottom is.. * 98 mm 212 mm 200.40 mm 89.50 mm

A: GIVEN DATA DEPTH OF WEB, DW=300 mm WIDTH OF WEB, BW=12 mm DEPTH OF FLANGE, DF=240 mm WIDTH OF…

Q: What is layerd cake

A: Layered cake:

Q: Define the Tensile load transfer ?

A: Solution: Tensile load transfer is defined as a measure of the capacity of a material to stand up to…

Q: Use the unit load method to calculate the vertical displacements at the quarter and mid-span points…

A: The given figure is shown below:

Q: Facts for Exterior doors.

A: Exterior doors should have certain requirements for the house.

Q: Structural Performance and Resistance to Wind and Rain.

A: The building envelope consists of the roof exterior walls, and exterior doors and windows.…

Q: what is force in FG

A: Given data in question  Force 60 kips Span 16 m Height 15 m To find out  Member force in FG

Q: A composite beam is fabricated by bolting two 2.5- in.-wide by 11-in.-deep timber planks to the…

A: Es = 30800 ksi Et = 1660 ksi Determine a. Maximum bending stress in timber and steel if P = 3.5…

Q: Why are pipes insulated?

A: Pipes are insulated to maintain temperature balance in the pipe. It also ensures avoiding of…

Q: How did u calculate minor and major stress

A: Minor and major stress

Q: Glass and Building Codes.

A: Solution:  Safety glazing is basically required for the fixed and operable panel of glass that will…

Q: * The area of a steel bar with dimeter of 16 mm is 0.3115 square inch 0.175 square inch 200.96…

A: Given: The diameter of the steel bar, ϕ=16 mm Also, 1 in = 25.4 mm⇒1 mm = 125.4 in⇒16 mm =…

Q: DETERMIME Fou つ こ I =

A:

Q: Name the several types of drive hammers.

A: The drive hammers are generally used for driving the pile in the pile foundation.   The several…

Q: Differentiate between elasticity and plasticity.

A: Elasticity:  Elasticity is the property of a material which regains it's original shape once the…

Q: Additional Problem: The wall crane supports a load of 7 kN. Determine the horizontal and vertical…

A:

Q: What is  negative skin friction ?

A: Friction is the resistance to motion of one object moving relative to another. It is not a…

Q: lap splicing

A: A lap splice is when two pieces of rebar overlap to form a continuous reinforcement. This helps…

Q: Describe the term compressibility.

A: Compressibility:- It is defined as the capability of the soil to decrease its volume under…

Q: ESSAY Advantages and Disadvantages of Using Hollow Block

A: Hollow blocks are generally prepared with aerated concrete . These block have both advantages as…

Q: the parts of the construction plan of a bridge and Horizontal structure.

A: BRIDGE:- Bridge is a structure that carries a road or railway across a river, valley, road or…

Q: make a report about glass blocks

A: Multiple units can join holes in basements and rooftops using glass blocks cast in a reinforced…

Q: Should one way slab be used for Steel Deck if the slab is a Square

A: Yes. Generally that is true.   The beauty of steel structures lie behind the short construction…

Q: give illustration or drawing of a model of strong bridge that will use bbq stick and bands.

A: One of real life example of strong bridge having concept of bbq stick and bands is golden bridge…

Construction Process

In civil engineering, construction is the combination of art and science, to construct a physical and naturally built environment, starting from the design phase. The construction process falls under the area of building construction, which is a sub-branch of civil engineering. Hence, it is also sometimes called the design and build or design-build process. The work of construction is majorly carried out by civil engineers and design professionals along with a team of works consisting of contractors and subcontractors.