A steel tape with a cross-sectional area of 0.03 sq. cm. is 30.00 m. long under a pull of 5 kg. when supported throughout. It is used in measuring a line 875.63 m. long under a steady pull of 10 kg. Assuming E=2.0x10^6 kg/sq. cm., determine the correct length of the measured line

A steel tape with a cross-sectional area of 0.03 sq. cm. is 30.00 m. long under a pull of 5 kg. when supported throughout. It is used in measuring a line 875.63 m. long under a steady pull of 10 kg. Assuming E=2.0x10^6 kg/sq. cm., determine the correct length of the measured line

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

This figure shows a cantilever beam that is subject to a point load and a moment. What is the vertical displacement at the tip of the beam? Assume E= 200 GPa and /= 1560 x 10 mm². A. 58.7 mm B. 68.9 mm C. 89.0 mm D. 100 mm 300 kN-m L=10m 60 KN
2. P Derive an equation that describes the vertical deflection of the beam, y(x), and also B calculate the maximum deflection of the beam. M = 0.5PL %3D
1. two decimal places
Determine the slope and vertical displacement of point A on the beam shown in the accompanying illustration. Use Conjugate Beam Method. E = 200,000 MPa
While tapping a hole, a machinist applies the horizontal forces shown, P= 3.35 lb and Q = 3.1 lb, to the handle of the tap wrench. Show that these forces are equivalent to a single force, and specify, if possible, the point of application of the single force on the handle. 3.2 in. D 25° 2.8 in. 25° B The single force is applied on an extension of handle BD at a distance of in. to the right of B.
Situation 22. For the built-up shape shown in the figure, determine: В. b, = 200 mm ty = 12 mm h = 200 mm tw = 10 mm 68. The location of plastic neutral axis form the top edge of the flange in mm. 69. The plastic section modulus about the horizontal axis. x10^6 mm^3 (3 decimal places) 70. The plastic moment with bending about the vertical axis if Fy = 345 MPa. KN-m (rounded to the nearest whole number)
A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. Determine the exact correction (m) to be applied due to slope if sag is neglected. * O 0.017 O 0.025 0.014 O 0.022
Determine the shear force and moment acting at point C of the beam shown in (Figure 1). For the calculation use Simpson's rule to evaluate the integrals. Follow the sign convention. Figure W 2 kip/ft w = (2x³ + √√x + 4)"> 2 ft 2 ft 1 of 1 11.58 kip/ft Part A What is the shear force at C? Express your answer in kilopounds to three significant figures. Vc = Submit Part B 15. ΑΣΦ Request Answer vec Beste ? What is the moment at C'? Express your answer in kilopound-feet to three significant figures. kip
Please show all steps.
3. A rigid bars shown in the figure are separated by a roller at C and pinned at A and D. A steel rod at B helps support the load of 50 KN. Compute the vertical displacement of the roller at C Answer: displacement = 2.82 mm E 200 X 10° N/m? %3D A = 300 mm? 50 kN L = 3 m 2 m 2 m A B 3 m 1.5 m II ()
A 30-meter steel tape weighing 1.45 kg is of standard length under a pull of 5 kg, supported for full length. The tape was used in measuring a line 938.55 m long on smooth level ground under a steady pull of 10 kg. Assume E=2.0x106 kg/cm? and the unit weight of steel to be 7.9x103 kg/cm3, determine the ff: a) Cross-sectional area of the tape b) Correction for increase in tension c) Correction length of the line measured
A uniform concrete slab is to be attached to two rods whose lowers ends are initially at the same level. What is the required area, in mm², of aluminum rod so that slab will remain level after it is attached to the rods? 4 m Aluminum E = 72 GPa Steel A= 96 mm < E = 200 GPa 4 m 3 m- 0.50 m