In the wood industries, inclined blocks of wood are sometimes used to determine the compression shear strength of glued joints. Consider the pair of glued blocks A and B in the figure below which are 38 mm deep in a direction perpendicular to the plane of the paper. Determine the shearing ultimate strength of the glue in MPa if a vertical force of 40 kN is required to cause rupture of the joint. 5 cm A 75 deg

In the wood industries, inclined blocks of wood are sometimes used to determine the compression shear strength of glued joints. Consider the pair of glued blocks A and B in the figure below which are 38 mm deep in a direction perpendicular to the plane of the paper. Determine the shearing ultimate strength of the glue in MPa if a vertical force of 40 kN is required to cause rupture of the joint. 5 cm A 75 deg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

When using a pencil eraser, you exert a vertical force of 8.00 N at a distance of 4.00 cm from the hardwood-eraser joint. The pencil is 8.00 mm in diameter and is held at an angle of 30.0° to the horizontal. (a) By how much does the wood flex perpendicular to its length? (b) How much is it compressed lengthwise?
A rectangular cross-section of a reinforced concrete beam is shown in the figure. The diameter of each reinforcing bar is 16 mm. The values of modulus of elasticity of concrete and steel are 2.0 x 104 MPa and 2.1 x 105 MPa, respectively. 200 mm Centroidal axis 35 mm The distance of the centroidal axis from the centerline of the reinforcement (x) for the uncracked section (in mm, round off to one decimal place) is 350mm
FE.Question 3.K
Properties: Rod 1 8F D = 40 mm d = 20 mm L = 1.3 meter E = 80 Gpa ROD 1 ROD 2 Rod 2 D = 80 mm d = 20 mm L = 1.0 meters E = 80 Gpa 3F 2. The composite rod shown in the figure is composed of three rods rigidly welded together. Applied forces in terms of "F" are exerted in different parts of the composite rod. Compute the maximum safest value of "F" if the allowable total deformation of the composite rod is limited to 0.50 mm only. ROD 3 2F Rod 3 D = 60 mm d = 20 mm L = 1.2 meters E = 80 GPa 7F
Q2/ A rectangular block of rubber is deformed as shown by the dotted line. Determine the average normal strain of line BD. Values shown are in mm. 450 A -4- B 300 C D 2.5
The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 25 mm, an inside diameter of 20 mm, and a shear modulus of G1 = 41 GPa. The solid steel core has a diameter of 20 mm and a shear modulus of G2 = 82 GPa. Assume L = 350 mm. The composite shaft is subjected to a torque of T = 910 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. T (1) (2) В
PLEASE SHOW THE COMPLETE AND CORRECT SOLUTION with fbd. Please don't post this question on google. Please. Subject : Strength of Materials ( Economic Section)
I need explanation and formula , Please do not copy paste the same solution.
The figure below shows a 1.3-in.-diameter ball loaded in compression by a 2600 lb force against the left end of a bar where the cross section is 1.7 in. x 1.7 in. The balls are hardened steel and the steel bar has a yield strength of 45 ksi. What maximum contact stress will result from the load of F = 2600 lb? Submit your answer in ksi. F F. 10 16 18
Determine the plastic moment Mp of the cross section shown when the beam is bent about a horizontal axis. Assume the material to be elastoplastic with a yield strength of 169 MPa. 5 mm t=5 mm 120 mm 5 mm 80 mm The plastic moment is kN.m.
The composite shaft, consisting of aluminium, copper, and steel sections, is subjected to the loading shown in Figure Q1. The modulus of elasticity of Aluminium Ea = 69GPA, modulus of elasticity of Copper Ecu = 117 GPa and modulus of elasticity of Steel Eg = 200 GPa. The composite shaft is circular in shape. 50 mm C 15 kN В 30mm 30 10 kN A mm 15 kN 25-kN 10 kN 15 kN 500mm 500mm 500mm Aluminium Eal = 69 GPa Steel Сорpr Ecu = 117 GPa Es = 200 GPa %3D Figure Q1 Determine the displacement for each material components. Aluminium Component(End B in respect to A) (i) (ii) Copper Component(End C with respect to B) (iii) Steel Component(End D with respect to C)
4.20 A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the magnitude of the load required to produce a 10 in. change in diameter if the deformation is entirely elastic. Assume a Young's modulus of 11 X 106 psi and a Poisson's ratio of 0.33.