13. A steel tape with a cross-sectional area of 0.03 cm^2 is 30.0 m long under a pull of 5 kg when supported throughout. It is used in measuring a line 875.63 m long under a steady pull of 10 kg. Assuming E=2.0x10^6 kg/cm^2, the elongation of the tape due to increase in tension is a. 0.0730 m b. 0.730 m c. 0.50 m d. 0.043 m e. 0.0025 m 14. The correct length of the measured line in 13 a. 875.56 m b. 875.63 m c. 875.68 m d. 875.60 m e. 875.70 m

13. A steel tape with a cross-sectional area of 0.03 cm^2 is 30.0 m long under a pull of 5 kg when supported throughout. It is used in measuring a line 875.63 m long under a steady pull of 10 kg. Assuming E=2.0x10^6 kg/cm^2, the elongation of the tape due to increase in tension is a. 0.0730 m b. 0.730 m c. 0.50 m d. 0.043 m e. 0.0025 m 14. The correct length of the measured line in 13 a. 875.56 m b. 875.63 m c. 875.68 m d. 875.60 m e. 875.70 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

700 mm (2) 650 mm 80 kN 870 mm (1) 900 mm 650 mm Determine the internal forces and normal stresses in bars (1) and (2). Indicate if it is in Tension or Compression. Also, determine the deflection of the rigid bar in the x direction at C. Bar Properties: Area 1 = 550 mm^2 E1 = 100 GPa Area 2 = 400 mm^2 = 100 GPa E2
Can you please answer this question
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E= 200,000MPa and a 11.7 Neglect bending of the beam. FF A=640mm2 A=320mm2 D 1.2m 0.8 m 1.2m V 54KN What is the vertical displacement of D when there is no change in temperature in mm?
Rigid bar ABCD is supported by two bars as shown in Figure P2.7. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (2) is measured as –3,300 um/m. Use the dimensions L1 = 1,600 mm, L2 = 1,200 mm, a = 240 mm, b = 420 mm, and c = 180 mm. Determine:(a) the normal strain in bar (1).(b) the normal strain in bar (1) if there is a 1 mm gap in the connection at pin C before the load is applied.(c) the normal strain in bar (1) if there is a 1 mm gap in the connection at pin B before the load is applied.
6. A tapered bar of length 600 mm is having cross sectional areas of 650 mm? and 350 mm? at two ends. The bar is fixed at the end having larger area and subjected to axial forces 40 kN which is acting axially outwards at the smaller end and 20 kN, acting at a point 200 mm from smaller end and directing axially towards the larger side. The Modulus of Elasticity of the bar is 700 x 103 N/mm2. Model the bar with three finite elements and Determine i The nodal displacements. ii The stresses in each element. iii The reaction force at the support.
A steel tape with a cross-sectional area of 0.03 sq. cm is 50.00 m long under a pull of 5 kg when supported throughout its length. It measures a line 857.63 m long under a steady pull of 10 kg. Assuming E = 2.0 x 10 to the power of 6 kg/sq. cm, what is the elongation of the tape due to the increase in tension? 0.0024 m b. 0.0250 m c. 0.0042 m d. 0.2500 m O a.
A 30-meter steel tape weighing 1.45 kg is of standard length under a pull of 5 kg, supported for full length. The tape was used in measuring a line 938.55 m long on smooth level ground under a steady pull of 10 kg. Assume E=2.0x106 kg/cm? and the unit weight of steel to be 7.9x103 kg/cm3, determine the ff: a) Cross-sectional area of the tape b) Correction for increase in tension c) Correction length of the line measured
3. Please show your complete solution.
Do the construction contractor protect the utility reference stakes and use the suitable construction techniques to protect the structure?
where, bf1= 260 bf2 = 120 tf = 25 tw = 16 d1 = 160 d2 = 110 1. Calculate the location of the neutral axis from the bottom of the beam in mm. 2. Compute for the moment of inertia in 1x10^6 mm^4. 3. What is the value of in kN/m, considering flexural stress in tension? 4. What is the value of in kN/m, considering flexural stress in compression? 5. What is the statical moment of area (Q) in 1x10^3 mm^3 ? Use three decimal places. 6. What is the value of in kN/m, considering shear stress at the welded section? 7. What is the safest value of in kN/m? Use three decimal places.
The 25-lb rectangular plate has a natural period of vibration t = 0.4 s, as it oscillates around the axis of rod AB. Neglect the mass of the rod. Suppose that a = 2 ft. b = 4 ft. (Figure 1) Figure Part A Determine the torsional stiffness of the rod, measured in lb-ft/rad. Express your answer in pound-feet per radian to three significant figures. ΕΠΙΑΣΦvec k= ^ A ? lb-ft/rad
There is a beam subject to a uniform force w as shown in the figure below. The E of the entire section is 200 GPa and I is 60x10^6 mm^4. (a) Calculate the reaction force at point c and the vertical displacement at point B (b) If the support point C sinks downward by 0.1m for some reason, calculate the reaction force at point C and the vertical displacement of point B.