A steel tape with a cross-sectional area of 0.03 sq. cm is 50.00 m long under a pull of 5 kg when supported throughout its length. It measures a line 857.63 m long under a steady pull of 10 kg. Assuming E = 2.0 x 10 to the power of 6 kg/sq. cm, what is the elongation of the tape due to the increase in tension? O a. 0.0024 m O b. 0.0250 m O c. 0.0042 m O d. 0.2500 m

A steel tape with a cross-sectional area of 0.03 sq. cm is 50.00 m long under a pull of 5 kg when supported throughout its length. It measures a line 857.63 m long under a steady pull of 10 kg. Assuming E = 2.0 x 10 to the power of 6 kg/sq. cm, what is the elongation of the tape due to the increase in tension? O a. 0.0024 m O b. 0.0250 m O c. 0.0042 m O d. 0.2500 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

X = 193 Y = 93 A = 2 B = 7 C = 9
A horizontal beam of length 3.00 m and mass 2.00 kg has a mass of 1.10 kg and width 0.170 m sitting at the end of the beam (see the following figure). What is the torque of the system about the support at the wall? Wall support 3 m, 2 kg 0.17 m. 1.1 kg Submit Answer Tries 0/40 4
Teemo is trying to move the crate weighing 15 kN by pulling on the rope at an angle 0 to the horizontal. T. 11. Find the smallest possible force that Teemo should pull to cause the crate to slide. Coefficient of static friction is 0.25. 12. Determine the angle 0. 13. Determine the horizontal frictional force acting at the bottom of the crate. 14. Determine the angle of static friction? 15. If Teemo pulls the crate at the force 5kN, will the crate move? (Prove your answer mathematically)
The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-sectional areas of 190 mm2 and 290 mm2, respectively. A uniformly distributed load of w= 12 kN/m is applied on the rigid beam as shown in the figure. Assume L= 3 m, a= 1.7 m, length of rods= 2.1 m and E= 57 GPa. Determine the force in rod (1)? Determine the force in rod (2)? Determine the normal stress in rod (1)? Determine the strain in rod (1)? Determine the deformation in rod (1)? In mm Determine the deformation in rod (2)?in mm
A rigid, uniform, weightless, horizontal bar is connected to three vertical members P, Q and R as shown in the figure (not drawn to the scale). All three members have identical axial stiffness of 10 kN/mm. The lower end of bars P and R rest on a rigid horizontal surface. When NO load is applied, a gap of 2 mm exists between the lower end of the bar Q and the rigid horizontal surface. When a vertical load W is placed on the horizontal bar in the downward direction, the bar still remains horizontal and gets displaced by 5 mm in the vertically downward direction.
5 decimal placesss 1. A bar of 16-mm in diameter is only allowed to decrease at a maximum of 4.84% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 630 MPa, and the Poisson's ratio as 0.36.
Statics homework #8
1. A simply supported beam with rectangular cross-section is loaded as shown in the figure. Draw the shear and bending moment diagrams and determine the maximum normal stress due to bending. |15 kN 6 kN/m E A В D 120 mm 0.8 m 2 m
Using the Clayperon Method, Determine: 1. Support Reaction 2. Internal forces (Shear Force, Normal Force and Bending Moment) 3. Draw the Internal force diagrams P1= 3.246 kN P2- 4.846 kN q- 1.846 kN/n s2 1,946 3,246 3,946 3,946 3,946 3,94268 L
Gate AB in figure below is a homogenous mass of 180 kg, 1.2 meter wide into the paper, resting on smooth bottom B. For what water depth hin meters will the force at point B be zero? Use specific weight of glycerin to be 12360 N/m³ and water to be 9790 N/m3. Water Glycerin h 2 m A 1 m 60° О а. 3.56 оБ. 1.82 О с. 1.12 O d. 2.52
A simply supported beam of length 7 m has a concentrated couple M of 10 kN-m applied at the right end. Determine the location of the maximum deflection from the applied load. O 2.75 m O 2.96 m O 2.50 m O 2.252 m Calculate the value of the maximum deflection. Use E = 200, 000 N/mm^2 and I = 60x10^6 mm^4. O2.62 mm O 131 mm 10.52 mm 5.26 mm