A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when subjected to an axial load of 10 KN. The same specimen undergoes a twist of 0.5° an a length of 150 mm over a twisting moment of 10 N-m. Using the above data, determine the elastic constants E,µ,G and K.

A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when subjected to an axial load of 10 KN. The same specimen undergoes a twist of 0.5° an a length of 150 mm over a twisting moment of 10 N-m. Using the above data, determine the elastic constants E,µ,G and K.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. Anaxial load of P = 30,500 lb. produced a deformation of 0.00103 in. over a gauge lengthof 2 in. and a decrease of 0.000078 in. in the 0.5-in. thickness of the bar. Determinea. Poisson’s ratio,b. the elastic modulusc. the decrease in the 4-in. cross-sectional dimension.
Vol. Strain.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN. 0.8m 0.4m B 5KN 0.6m Al 20KN Q2 5) What is the deformation 8, in mm? A=800 mm? A=1,200 mm?
PROBLEM 37: A sieel secion havung a Cioss seciion c: 20 mm x 30 mm is subjected to an axial force of 240 KN The steel section has produces a strain of 0.002. If it has a value of Poissons ratio of 0.30.Find the shear modulus a. 76923 MPa b. 73852 MPa C. 78023 MPa d. 80256 MPa
I need the answer quickly
3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2. Take maximum tensile stress for cast iron as 14 MPa. [Ans. 6.25 mm]
i need the answer quickly
y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.