A steel bar, 300 mm long and 24 mm diameter, is turned down to 18 mm diameter for one third of its length. It is heated 30°C above room temperature, clamped at both end and then allowed to cool to room temperature. If the distance between the clamps is unchanged, the maximum stress in the bar (a = 12.5x10-6 per °C & E=200GN/m²is)

A steel bar, 300 mm long and 24 mm diameter, is turned down to 18 mm diameter for one third of its length. It is heated 30°C above room temperature, clamped at both end and then allowed to cool to room temperature. If the distance between the clamps is unchanged, the maximum stress in the bar (a = 12.5x10-6 per °C & E=200GN/m²is)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

the cross-sectional area of the bar 1 of the two bars supported on the left and right sides is 1.2 cm^2, the coefficient of thermal expansion is 20.9 10^(-6)/K; The cross-sectional area of bar 2 is 3 cm^2 and its coefficient of thermal expansion is 25.4 10^(-6)/K. Since the modulus of elasticity of the material is 207 GPa, these two bars are heated to 99 °C.a) What will be the change in length (mm) of bar 1?b) What is the stress in bar 1 in MPa?c) What is the stress in bar 2 in MPa?
A steel rod is fixed at one end and the other end has a distance of 0.2 mm from a rigid support. The rod is heated to increase its temperature by 200°C. Calculate the stress developed in the rod. The elastic modulus of rod is 200 GPa and the coefficient of thermal expansion is 104per °C.
In a steel railroad, the 12 meters long rails are laid with a clearance of 5 mm at a temperature of 20 degrees centigrade. The modulus of elasticity of steel is 200 GPa. a) At what temperature will the rails just touch if the coefficient of linear expansion is 11.7x10^-6/°C.? b) Determine the stress in the rails at 65 °C
A solid aluminum (E = 70 GPa] rod (1) is connected to a solid bronze (E = 93 GPa] rod (2) at flange B, as shown. Aluminum rod (1) has an outside diameter of 34 mm and bronze rod (2) has an outside diameter of 16 mm. The normal stress in the aluminum rod must be limited to 139 MPa, and the normal stress in the bronze rod must be limited to 103 MPa. Assume L1 = 166 mm and L2= 359 mm. Determine: (a) the maximum downward load P that may be applied at flange B. (b) the deflection vg (downward is positive) of flange B at the load determined in part (a). C L2 B P. (1)
Spleb this fast.
The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature.
The degree to which the theoretical value of stress concentration is actually reached is called as
2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the alu- minum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. - 14 in. - Bronze A = 2.4 in² E = 15 x 106 psi a = 12 x 10-6/°F Fig. P2.58 and P2.59 18 in.. Aluminum A = 2.8 in² E = 10.6 x 106 psi a = 12.9 x 10-6/°F 300 mm 0.5 mm 250
The state of stress at a point is shown with respect to xy-plane. The state of stress at a point is shown with respect to x'y'-plane? 8 MPa y'v 60° S MPa +S MPa 10 MPa 8 MPa
At an axial load of 20 kN, a 45-mm-wide by 10-mm-thick polyimide polymer bar elongates 3.3 mm while the bar width contracts 0.21 mm. The bar is 240 mm long. At the 20-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= i i i GPa mm
A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by 50°C. If rod is allowed to expand by 14 mm, what will be the stress induced in rod? Take E = 200 GPa and α = 12 x 10-6/°C.
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)