A steam pipe weighing 200 kg per meter will cross a road by suspension on a cable anchored between supports 6 meters. apart. The maximum allowable sag of the cable is 50 cm, calculate the length of the cable.

A steam pipe weighing 200 kg per meter will cross a road by suspension on a cable anchored between supports 6 meters. apart. The maximum allowable sag of the cable is 50 cm, calculate the length of the cable.

Name: A steam pipe weighing 200 kg per meter will cross a road by suspension
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A steam pipe weighing 200 kg per meter will cross a road by suspension on a cable anchored between supports 6 meters. apart. The maximum allowable sag of the cable is 50 cm, calculate the length of the cable..

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

Two spheres, each 1.20 m in diameter, weighs 4kN and 12kN respectively. They are connected with a short rope and placed in water. Find the tension in the rope in kN
A ladder 12 m long leans against a vertical frictionless wall with its lower end 3 m from the wall. The ladder weighs 40 N. Find the magnitude and direction of the force exerted on the lower end of the ladder.
. Aluminum bolts 2cm in diameter and 500cm long are used to hold the head on a pressure vessel. One bolt has a sensitive extensometer attached to the body of the bolt. It measures an elongation of 0.00400mm in a ten-cm length of the bolt when it is tightened. How much force is exerted by the bolt?
A uniform, 7.5-m-long beam weighing 6490 N is hinged to a wall and supported by a thin cable attached 1.5 m from the free end of the beam. The cable runs between the beam and the wall and makes a 40° angle with the beam. What is the tension in the cable when the beam is at an angle of 30° above the horizontal?
Calculate the force P required to keep the gate closed.
Calculate the Force on a piston when the Pressure applied P= 50 psi and the area of the piston is 20 in.2
a cylinder that is 500 mm in diameter and 2.0 m long has a specific weight of 535 N/m3 . It is held down into position with a cable attached to the sea floor. At this location, the sea is 500 m deep and the cylinder is to held in a fully submerged position just 3 m above the sea floor. FInd the resulting tension in the cable.
A cylinder suspended by a rope rests against an inclined surface as shown. If the cylinder weighs 1700 N, 0 = 53 degrees and ø = 98 degrees, find the tension in the rope (above the knot) and the normal force between the cylinder and the inclined surface. 2013 Mchael Swanbom
Answer number #2 and make a detailed solution such as the unit cancellation, and its conversions so that I can understand the process because I am new in engineering. Thankyou so much!
A hydraulic jack is used to raise a 10KN car. A force of 400N applied on a 25mm diameter jack plunger. What diameter of jack in mm is required to raise the car?
A slab of rock is tilted upwards and is held steady by a rope (CB). The rope is attached to anearby wall (at point B). The slab of rock is of uniform density (50 kg/m2), and is isosceles in hape, as shown in the figure below. Determine the tension in rope CB, as well as the Fx and Fyreaction force components on the bottom edge of the rock where it rests on rough ground. Expressthe reaction force components in Cartesian vector form
1. What force is required to keep the 5 ft wide gate closed. Neglect the weight of the gate. 10 ft H,0 Hinge 8 ft 6 ft