Answered: A hydraulic jack is used to raise a…

A hydraulic jack is used to raise a 10KN car. A force of 400N applied on a 25mm diameter jack plunger. What diameter of jack in mm is required to raise the car?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.17P: A man weighs 170 lb on the surface of the earth. Compute his weight in an airplane flying at an...

See similar textbooks

Related questions

Q: I have a bolt that has a cross-sectional area of .75 sq. in., I pull on the bolt with a force of…

A: Bolt is a cylindrical shape body having head on its top and threads in lower part along the length…

Q: 1. A hydraulic press has a ram of 30 cm diameter and a plunger of 4.5 cm diameter. Find the weight…

A: Diameter of ram, D1=30cm⇒0.3m Diameter of plunger, D2=4.5cm⇒0.045m Force applied at plunger, F2=500N…

Q: Ten and one-half foot-pounds of work is required to compress a spring 2 inches from its natural…

A: Given data Work = 10+1/2 (lb-ft) Initial compression = 2in Find the work required to compress the…

Q: The top of the circular table shown to the side is 1.2 meters in diameter and weighs 26 kg. If a 90…

A: Solution: Given Data: D=1.2 mm=26 kgM=90 kg To Find: The diameter of the circular base of the…

Q: A semicircular plate of radius 5ft rests vertically on its diameter at the bottom of a pool filled…

Q: difference between the total downward force at the top of the cube, and the total upward force at…

A: Given: The atmospheric pressure is, Patm=1atm=1.01×103 Pa. The density of liquid is, ρ=1039 Kg/m3.…

Q: A load of 150 lbs is exerted on a piston confining oil in a circular cylinder with an inside…

A: Write the expression to obtain the area of the piston.

Q: 2.18 A rope tow is used to pull skiers up a snow-covered slope that is 1000 ft long and has a slope…

Q: An aluminum cube with an edge of 5 cm is resting on the ground on one of its faces. calculate the…

A: Given data s= 5 cm = 0.05 m d= 2700 kg/m³ Note: diagram is not necessary for the understanding…

Q: The Diameters of a small piston and a large piston of a hydraulic jack are 5 cm ad 10 cm…

Q: A 10 ft by 15 ft rectangular cistern (storage tank for rainwater) has its top 30 ft below ground…

A: Calculus is frequently used to determine the amount of labour required to empty a tank of the…

Q: Diagram of the problem, necessary formulas, clearance and numerical solution It is planned to lift…

Q: EG 2.5 2.5 E DT 2.6 В Acotaciones en ft 3.2 2.4- www.B

Q: A block of wood 0.20 m thick is floating in sea water. the specific gravity of wood is 0.65 while…

A: Given Thickness, t = 0.2 m Specific gravity of wood, SGw =…

Q: Question 2 A 5 foot by 5 foot square plate is placed in a pool filled with water to a depth of 8…

Question

A hydraulic jack is used to raise a 10KN car. A force of 400N applied on a 25mm diameter jack plunger. What diameter of jack in mm is required to raise the car?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

1. A hydraulic press has a ram of 30 cm diameter and a plunger of 4.5 cm diameter. Find the weight lifted by the hydraulic press when the force applied at the plunger is 500 N.
The handle of a small hand pump is 850mm long. The fulcrum is attached at one end and the load plunger is located 50 mm from the fulcrum. An effort of 600N is applied downward at the opposite end from the fulcrum. Find the force exerted by the load plunger and the mechanical advantage of the lever.
This a not graded assignment, it is a question on a practice exam. Please do question 6.
3
Two circular platforms are attached to a fluid reservoir. On one platform rests seventeen baby armadillos.. A force of 3.4 N is applied downward to the empty platform with radius 9.8 m. The area of the other platform has radius 2.3 m. How much force is applied to the platform with the armadillos?
A 3000 pound force is applied to a piston causes a pressure of 800 psi. What is the diameter of the piston to which the force is applied?
The diameter of the small cylinder of a hydraulic press is 6 inches while the diameter of its large piston is 10 inches. If a 140 lb. of force is applied at the small piston and neglecting friction, what is the force on the large piston.
Use the formulas for the hydraulic press to find the value. A force of 30 lb is applied to a piston of radius 5 in. of a hydraulic press. The large piston has a radius of 25 in. What force (in pounds) is exerted by the large piston?
A wooden plank x meters long has one end leaning on top of a vertical wall 1.5 m long and the other end resting on a horizontal ground. Neglecting friction, find x if a force (parallel on the plank) of 100 N is needed to pull a 400 N block up the plank.
Diagram of the problem, necessary formulas, clearance and numerical solution An aluminum cube with an edge of 5 cm is resting on the ground on one of its faces. calculate the pressure in Pascals that it exerts on the ground knowing that the density of aluminum is 2700 kg/m3.
Lipkin is standing on a scale while leaning with his hands on a wall at an angle of 600. Draw a free body diagram. If Lipkin’s wt. is 100 lb.s normally, what should the scale read in this case?
Q3: The diagram shows the open bonnet of a car. The bonnet is vertical force V held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The car bonnet bonnet is 0.90 m long, has a weight of 25 N and its center of gravity G is 0.35 m from the hinge at O. 0.90m 1) On the diagram, draw and label the two forces other than V acting on the bonnet. 2) By taking moments about O, show that the vertical force V applied at the end of the bonnet is 9.7 N. 60 horizontal hinge O 3) Calculate the magnitude of the force acting at the hinge O.