A steam generator burns fuel oil with 22% excess air. The fuel oil is dodecane. The fuel gas leaves the preheater at 0.30 MPa. Determine the actual air fuel ratio

Q: 4. If the isentropic efficiencies of the turbine and the pump are 80% and 100% respectively in…

A:

Q: Find the minimum exhaust temperature

A: Given: 80% C12H36 and 20% C14H30 burnt with 30% excess air flue gas at atmospheric pressure To…

Q: 4. Steam enters the turbine at 10 MPa and 500 °C with mass flow rate of 10 kg is condensed in the…

A: As per guideline we can solve one question at a time please post other question separtaly . Given…

Q: Define Diesel Electric Power Plant

A: Diesel electric power plant- it is a power plant which work on the principal of energy conversion…

Q: 4) If ethane is used as the fuel for the Brayton cycle, conduct an analysis of its complete…

A:

Q: What are the procedures in starting a self-starting diesel power plant

A: Introduction- Because diesel is a fossil fuel, this is a fossil fuel plant. Where coal and water…

Q: With a neat diagram indicating all the parts, explain the working of the diesel power plant (Any…

A:

Q: Explain Diesel-fired power plant

A: A generating station during which diesel motor is employed because the first cause for the…

Q: How does reheating allow for improved Rankine cycle performance?

A: step by step solution is given below,

Q: Explain the processes of a Rankine Cycle. List the types of fuel used

A:

Q: Natural gas with an analysis as follows CO2 = 0.4% CH4 = 97.3%, N2 = 2.3%, is burned in a furnace.…

A:

Q: 1. In an ideal dual combustion cycle, what is the pressure at the beginning of constant pressure…

A:

Q: i. Carbon Intensity what is this a measure of, what are its units and why is it important? ii.…

A: To explain:i. Carbon Intensity what is this a measure of, what are its units and why is it…

Q: Calculate the exhaust gas composition of a butane-fuelled spark-ignition engine operating with…

A:

Q: what is the pressure ratio in an ideal dual combustion cycle if the pressure at the beginning and…

A: Given data,  P2= 2500 KPa  P3= 4000 KPa

Q: A fuel has the following constituents: carbon 85%, hyrdogen 13%, oxygen 2%. When burning this fuel…

A: GivenC=85%H=13%O=2%air supply is 50% in excess

Q: Instructions: Perform a cycle analysis for the given reheat-regenerative Rankine cycles. Supply the…

A:

Q: The fuel cell has moving parts.

A: The fuel cell has ________ moving parts. Answer: No

Q: In Case of the Gas power plant, Clearly Identify at least 12 Important parts. Explain the kind of…

A: Solution : The parts of gas turbine power plant : Heat exchanger Chimney Cooler Electric motor High…

Q: Q1/ Steam enters the turbine at 30 bar, 400°C, amount of steam is extracted at 5 bar to a single…

A:

Q: Name the biogas plant in which the volume of stored gas is not directly visible? Fixed dome type…

A: Given Data→ Biogas plant

Q: Which cycle is being used to analyze coal based steam power plants? Otto cycle Rankine cycle…

A: Which cycle is being used to analyze coal based steam power plants? Otto cycle Rankine cycle…

Q: With a neat diagram indicating all the parts, explain the working of the diesel power plant (Any…

A: Answer:

Q: ext gases. 28 lb/hr. Assuming t n air-fuel ratio of 15 e volumetric efficior Hicion

A:

Q: An advantage of using natural gas, rather than oil, as a fuel is that natural gas is?

A:

Q: What is a combined cycle power plant (CCPP)? Describe briefly using schematic diagram.

A:

Q: recirculated

A:

Q: Determine the ideal air-fuel ratio of an engine wh

A: an octane rating, or octane number ,is  a standerd measure of a fuel s ability to to withstandard…

Q: How to Calculate the thermal efficiency of 400 MWth PBMR. PBMR, Helium using Brayton Cycle

A:

Q: IE C3H6 (0.00004 kg) in a cylinder during the combustion start-up cycle T = 600K & p = 2000 Kpa The…

A:

IC engines

The term "engine" indicates a mechanical device/machine used to convert input energy to a specific mechanical output. The input energy may be in the form of chemical energy, thermal energy, or so on and mechanical output is in the form of mechanical energy (work done). Generally, the engines classify into two groups which are internal combustion type and external combustion type, and further, these two types can be classified into two types that are reciprocating and rotary engines.