=A standard penetration test is carried out in sand where the efficiency of the hammer n50%. If the measured N-value at 7.5 m depth is 20, find Noo and (N₁)60. The unit weight of the sand is= 15 MR= 1 and18.08 kN/m³. Assume ¹= 0.95. If you know that:ns

nH = 50%N = 20 = 18.08 kN/m3 nB = 1ns = 1nR = 0.95

A standard penetration test is carried out in sand where the efficiency of the hammer ₁ 50%. If the measured N-value at 7.5 m depth is 20, find Neo and (N₁)so. The unit weight of the sand is 18.08 kN/m³. Assume n = 1 and = 15 1R = 0.95. If you know that: ns = 15 mR

A standard penetration test is carried out in sand where the efficiency of the hammer ₁ 50%. If the measured N-value at 7.5 m depth is 20, find Neo and (N₁)so. The unit weight of the sand is 18.08 kN/m³. Assume n = 1 and = 15 1R = 0.95. If you know that: ns = 15 mR

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ASAP. Answer is Given. Please show how to solve
For the attached problem if D50 =0.8 mm, findthe N60 values at each depth. Use Eq attached with Kulhawyand Mayne values for a and c.
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3.
(1) A well is drilling to the depth of 6000 m. Formation pore pressure can be expressed in equivalent mud weight is 1.50 g/cm' at the depth and changes in proportion to well depth. Also, overburden pressure gradient is 0.0245 MPa/m. Calculate: a. Pore pressure gradient at 6000 m, MPa/m. b.Pore pressure, psi, at 6000 m. c. Matrix stress gradient, MPa/m d.Matrix stress at 6000 m, MPa
4. The construction of a 10m x 10m square water tank in a residential neighbourhood has been planned. As indicated in Figure below, a 6m thick soft clay layer was discovered between sand layers during site exploration. For laboratory studies, an undisturbed soil sample was obtained in the middle of the soft clay layer. The findings of the laboratory consolidation test are listed below. Pressure, o' (kN/m2) | 25 50 100 200 400 800 Void Ratio, e 1.28 1.26 1.22 1.14 1.05 0.95 i. Find the preconsolidation pressure (o'c), Virgin, and Laboratory Compression Index using the information above (Cc). Find the primary consolidation settlements that will occur at the water tank's centre due to compression of the soft clay layer ii. 10 m Load = 18,000 kN Ground Level 1 m Ground water level Dense Sand, y= 20 kN/m³ 2 m Soft Clay Kat = 16 kN/m³ ; eo= 1.38 Cc = graph? ; Cs =Cc; o' = graph? 6 m %3D %3! Very Dense Sand
Please solve with all work shown. Thank you
In a drained triaxial test on consolidated clay the stress and angle are as follows : Deviator stress is 20 lb/in2 and friction angle 210 . calculate the effective confining pressure at failure.?
It is known that a particular deposit of clay has the following shear strength parameters: c' = 15 kPa, o' = 23°; Cu = 10 kPa, cu = 13° A sample of this clay is consolidated in a triaxial cell to an all-round pressure (03) of 250 kPa. The sample is then sheared by increasing 0₁, keeping 3 constant and the drainage valve closed. What is: i) ₁ at failure? ii) Pore water pressure inside the sample at failure? iii) Final values of 0₁' and 03'? iv) Value at failure of Skempton's pore pressure coefficient A?
A consolidated-undrained test on a normally consolidate clay yield the following results: Confining Pressure = 151 KPa; Deviator Stress = 187 KPa; Pore Pressure = 71 KPa. Calculate the consolidated undrained friction angle. Please answer this asap. For upvote. Thank you very much
x 18 The effective shear strength equation (S = T₁ = 25+5 tam 30); expressed for a saturated clayey soil. In undrained test on a sample of the same soil using the shear box apparatus, the following data at failure were recorded :. Shear Stress = 90 kPa a) What and Normal stress = 180 kPa pore water pressure in the specimen at time of was the failure (assume Øu= 0). Find the Unconfined compressive strength (Od max) for the same soil an Unconfined. when tested in Compression test. c) Find the major principal stress when a sample of the same soil is tested in Ul test with confining pressure of (200 kPa).
Question A sample of dry sand was tested in direct shear test apparatus under a normal load of 72 kg. The shear load required to fail the sample was found to be 36 kg. The angle of internal friction () will be:
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3. a. 177.38 b. 354.75 c. 88.69 d. 709.5