A square metal plate with mass M=6.00 [kg] and side length 3.00 [m] is pivoted about an axis through point O at its center and perpendicular to the plate. Three forces of magnitude F1=36.0 [N], F2=24.0 [N], and F3=40.0 [N] act on the plate as shown. A.  What is the net torque on the square plate due to these forces? Is the direction in or out of the paper? B.  What is the angular acceleration of the plate? The moment of inertia for a plate of length a and width b rotating about its center is Icom =(1/12) M(a2 + b2) Is the direction in or out of the paper? C.  If the plate is initially at rest, what is the angular velocity of the particle after 2.70 [s] Is the direction in or out of the paper?

Q: Two horizontal rods are each held up by vertical strings tied to their ends. Rod 1 has length L and…

A: Given:Length of rod 1 si L,Mass of rod 1 is M Length of rod 2 is 2L and Mass of rod 2 is 2M.

Q: A merry-go-round accelerates from rest to 0.69 rad/s in 31 s. Part A Assuming the merry-go-round is…

A: Torque.

Q: A uniform drawbridge must be held at a 41.0° angle above the horizontal to allow ships to pass…

A:

Q: 90° 125 N 90 90.0 N

A:

Q: A square metal plate with mass M = 6. 00 [kg] and side length 3.00 [m] is pivoted about an axis…

A: The free-body diagram of the given force system is shown below.

Q: Two forces are applied to a merry-go-round with a radius of 1.2 m. One force has a magnitude of 80 N…

A: radius = r = 1.2 mtwo forces F1 = 80 N (UP)F2 = 50 N ( Down)

Q: F2 F- 2.750 m 45° F3 2.750 m

A:

Q: The ball has a mass of 80 grams and is moving 10 m/s. The rod has a mass of 500 grams and a radius…

A:

Q: An engineer applies a force of magnitude F=15 N to the tip of a vertical lever. The force has an…

A:

Q: Two kids (one with mass mA=33.5kg and the other with mass mB=32kg) sits on the edges of a 2.56-m…

A: Given: The mass of object A is 33.5 kg. The mass of object B is 32 kg. The length of the see-saw is…

Q: 2.750 m A square metal plate with mass M = 5.80 (kg] and side length 2.75 (m] is pivoted about an…

A: Give mass 5.8kg side length is 2.75m three magnitude forces F1 is 40N F2 is 48 N F3 is 36N . We have…

Q: A uniform door weighs 51.00 N and is 1.100 m wide and 2.400 m high. What is the magnitude of the…

A: Given data: The weight of the door is W=51 N. The height of door is h=2.4 m. The width of the door…

Q: A 6.20 [kg] square plate has side length of 3.25 [m] and is pivoted about an axis through its center…

A:

Q: A uniform, 255 N rod that is 1.80 m long carries a 225 N weight at its right end and an unknown…

A: Step 1:Weight of the rod is 255NWeight placed at the right end of the rod is 225NPosition of the rod…

Q: 9. The picture below shows a rod of mass 4.50 kg which is free to rotate horizontally about one end…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: The figure below shows forces acting at various points on a metal shaft. The angles ? = 48°, ? =…

A: Given data, Angels, α=48°β=35°γ=21° Length l=3.6 m

Q: You exert a force   on a "blob" at a point  x0 , y0 (4.5m, 3.1m)   as shown in the figure. What is…

A:

Q: A thin rod is suspended on a hinge and has a horizontal force of 90 N applied at the endpoint B. The…

A:

Q: A uniform solid disk with a mass of 29.5 kg and a radius of 0.407 m is free to rotate about a…

A:

Q: As shown below, a 25 kg bar that is 1.8 m long is set up to rotate about its center (the yellow…

A:

Q: Two disgruntled businessmen are trying to use a revolving door, as shown in the figure. The door has…

A:

Q: How much torque would it take to make the wheel speed up from rest to 1.5 rev/sec in 10 sec? b. Now…

A: The moment of inertia of a rigid body is the sum of the products of the masses of all the particles…

Q: Calculate the magnitude and direction of the net torque about point P for the three forces applied…

A:

Q: 10.0 N 30.0 12.0 N b. 9.00 N Consider the figure above, which shows a brass axle of radius a…

A: The problem is based on the concept of Torque of force about an axis of rotation. Let O is the axis…

Q: When there is no food in my microwave oven, the acceleration of the turntable is 0.150 rad/s2. The…

A:

Q: 2.A What torque does a force of 18 N exert if it is exerted perpendicular to a wrench and distance…

A: Given data:  Force (F) = 18 N Arm length (r) = 0.15 m Angle (θ) = 90°

Q: Two 80 N forces are applied to opposite corners of a rectangular plate of length b and width a, as…

A:

Q: A disk of mass M = 2.0 kg and radius R = 0.25 m is free to rotate about its center. Two forces, F1 =…

A: The mass of the disk is m = 2 kg. The radius of the disk is r = 0.25 m. The applied force F1 = 1.0…

Q: A break is applied to a wheel with a moment of inertia equal to 150 kg m2. The wheel's angular…

A:

Q: Tom and Jerry both push on the 2.90-m-diameter merry-go-round shown in (Figure 1). Tom pushes with a…

A: Given Data: Diameter of the object (d) = 2.90 m.Hence, radius of the object (r) = 2.90 m2 = 1.45…

Q: A force of 129.00 N is applied on a rod at a distance of 11.00 m from the pivot point. As a result,…

A: Solution: given that F= 129 N R = 11 m angle = 39 degree

Q: A rigid beam of mass 7.12 kilograms and length 1.57 meters is fixed at point P, around which the…

A:

Q: Two forces are applied to a merry-go-round with a radius of 1.2 m. One force has a magnitude of 80 N…

A:

Q: A waiter holds two plates of food in one hand. His forearm has a mass of 2.8kg and the centre of…

A: Note: As per the guidelines, we can only answer first question of multiple question. Sorry for the…

Q: onsider a plywood square mounted on an axis that is perpendicular to the plane of the square and…

A: Side is ,a= 0.36 m Force ,F= 16 N To find Magnitude of maximum torque ,T= ?

Q: The figure below shows forces acting at various points on a metal rod. The angles α = 40°, B = 25°,…

A: (a) For an axis through O perpendicular to the page, the net torque is -30.6 Nm in the…

Q: 1. A spool of wire has a radius of 0.40 m and mass of 4.0 kg. If you pull the wire with a 20.0 N…

A:

Q: A triangular plate is acted on by three forces, as in the figure. Taking the +z- direction to be out…

A: Given, d1 = 2.7 md2 = 1.6 mF1 = 27 NF2 = 47 NF3 = 52 Nθ2 = 57°θ3 = 45° Torque, τ = r×F = rFsinθ, θ…

Q: A grindstone of mass M=30 kg and radius 0.50 m start from rest and experiences a constant angular…

A: M = 30 kg R = 0.5 m α = 3 rad/sec2

Q: A playground merry-go-round has a radius of 4.30 mm and a moment of inertia of 243 kg⋅m2kg⋅m2 and…

A: Radius of merry go round (R) = 4.3 m Moment of inertia (I) = 243 kg.m2A) Applied force (F) = 25 N…

Q: A 55-kg child sits on a 1.1-m radius playground merry-go-round without holding on to the rails.  a.…

A: mass of child m = 55 kg radius of merry-go-round r = 1.1 m torque τ = 356 Nm

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.